30 views
in Basic concepts by
A 40 W bulb is connected in series with a room heater. If now 40 W bulb is replaced by 100 W bulb, the heater output will?

Your answer

Thanks for your contribution. Feel free to answer this question. Please avoid short answer. Your answer is most welcome. Be genuine.

Upload image or document:

Your name to display (optional):
Privacy: Your email address will only be used for sending these notifications.
Anti-spam verification:
Are you a robot ? (Y = Yes / N = No)
To avoid this verification in future, please log in or register.

1 Answer

0 votes
by

A 40 W bulb is connected in series with a room heater. If now 40 W bulb is replaced by 100 W bulb, the heater output will increase.

Related questions

1 answer 20 views

A 500 W bulb fitted with a reflector illuminates an area of 2 m x 2 m with an average illumination of 500 lux. The efficiency of the reflector is 50%. The efficiency of the bulb in lumens/watt is : 

asked Apr 29, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 20 views

One 200 V, 100 W bulb is connected in series with primary of a 200 V, 10 kVA transformer. If its secondary is kept open circuited, then the bulb would have (1) Full brightness (2) Poor brightness (3) A little less than full brightness (4) More than full brightness 

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 28 views

Two light bulbs are connected in series across a 120 V battery. Bulb 1 uses 40 W of power and Bulb 2 uses 20 W of power. If bulb 1 alone is connected to the 120 V source, then it will consume (A) 90 W (B) 80 W (C) 60 W (D) 180 W

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

The filament of an electric bulb is made of?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 22 views

When current flows through heater coil it glows but supply wiring does not glow because?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 20 views

About how many times longer would a 10 watt light bulb be able to burn compared to a 100 watt bulb with the same energy?  (A) 10 times longer (B) 100 times longer (C) Same time (D) None of the above

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 26 views

In a series circuit with unequal resistances?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 16 views

Two resistances Rl and Ri are connected in series across the voltage source where Rl>Ri. The largest drop will be across?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 17 views

Two resistors are said to be connected in series when?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 23 views

What is the total resistance if 5 resistors of 20 Ω each are connected in series? A) 100 Ω B) 4 Ω C) 20 Ω D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance R.A. voltmeter having a resistance of 1.2 kOhm is connected across 600 Ohm resistance and read 5v. The value of resistance R will be

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 32 views

Consider a circuit with four resistors in series connected to a voltage source. What happens to the voltage across each resistor, if the value of each of the resistors is doubled? A) It will double B) It will remain the same C) It will be halved D) It will become zero

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

An inductor is connected in series with SCR to protect it from A) Excessive high voltage B) Excessive high dv/dt C) Excessive high di/dt D) Excessive large forward current 

asked Jun 18, 2018 in Inductor by Shimroz123
0 answers 20 views

Which type of heater is cheapest to run?

asked Mar 11, 2018 in Utilization of electrical energy by Quiz
0 answers 440 views

A 220 V, 200 W bulb and a 220 V, 100 W bulb are connected in series across a 220 V supply, the power consumed by them will be (a) 33.3 W (b) 66.6 W (c) 100 W (d) 300 W

asked May 25, 2018 in Electrical Engineering by Shimroz123
1 answer 19 views

A 100-watt light bulb turned on for 8 hours uses :  (A) 800 Wh (B) 0.8 kWh (C) 8 kWh (D) None of the above

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

Power factor of electric bulb is?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 5 views

State the location and function of i) Economizer ii) Feed water heater.

asked Sep 7, 2018 by Shimroz123
2 answers 77 views

 With three resistances connected in parallel, if each dissipates 20 W the total power supplied by the voltage source equals?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 22 views

What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively? A) 320 V B) 448 V C) 64 V D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 26 views

If resistance is 20 Q. and inductance is 27 in a R-L series circuit, then time constant of this circuit will be?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

Two incandescent light bulbs of 40 Wand 60 W rating are connected in series across the mains, then .  A) The bulbs together consume 100 W B) The bulbs together consume 50 W C) The 60 W bulb glows brighter D) The 40 W bulb glows brighter

asked May 20, 2018 in Network Analysis by Shimroz123
1 answer 21 views

Three 60 W bulbs are in parallel across the 60 V power line. If one bulb burns open?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 49 views

Two 100W, 200V lamps are connected in series across a 200V supply. The total power consumed by each lamp will be in Watts

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 31 views

A DC voltage source is connected across a series RLC circuit. Under steady-state conditions, the applied DC voltage drops entirely across the

asked Apr 29, 2018 in Network Analysis by Shimroz123
2 answers 31 views

The hot resistance of the bulb's filament is higher than its cold resistance because the temperature co-efficient of the filament is?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 75 views

 An independent voltage source in series with an impedance ZS=R+jXS delivers a maximum average power to a load impedance ZL when A) ZL = R B) ZL = jXS C) ZL = R-jXS D) ZL = R+jXS 

asked Jun 18, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

In a series R-C circuit, with the increase in frequency, current (A) Reduces (B) Increases (C) Does not change (D) Becomes zero

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 34 views

Cells are connected in series in order to?

asked Mar 16, 2018 in Electrical Engineering by Quiz
1 answer 15 views

The time constant of a series R-C circuit is given by?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 17 views

Which of the following is true with a series circuit having resistors of different values? A) The total resistance of the circuit is the sum of the individual resistances B) The current across each resistor is the same C) The voltage drop across each resistor depends on the value of the resistor D) All the above

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 10 views

The current through a flashlight bulb is 40 mA and the total battery voltage is 4.5 V. The resistance of the bulb is approximately? A.112 ohms B.11.2 ohms C.1.2 ohms D.18 ohms

asked May 15, 2018 in Basic concepts by Shimroz123
1 answer 18 views

In R-L-C series resonant circuit magnitude of resonance frequency can be changed by changing the value of?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 22 views

A series R-L-C Circuit has a resonant frequency of 1000 Hz. If the values of R, L and C are doubled, the new resonant frequency is

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 25 views

In a battery, the difference between the no-load voltage and the measured voltage output is called ________ A) Internal voltage B) Internal resistance C) External resistance D) All the above

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

In a series resonant circuit, the impedance of the circuit is?

asked Mar 24, 2018 in Electrical Engineering by Shimroz123
1 answer 19 views

Explain full wave bridged rectifier with the help of circuit diagram and input output waveform.

asked Sep 5, 2018 by Shimroz123
1 answer 47 views

Explain DC coupled drive circuit with unipolar output.

asked Feb 19, 2018 in Unit 5 by Quiz
1 answer 15 views

In a 2 kW, 200 V, 1000 rpm. DC series motor the torque at full load was found to be 0.3 N -m. The torque at half full load in N -m is :

asked Apr 29, 2018 in Electrical Machine by Shimroz123
1 answer 22 views

In a series RLC high Q circuit, the current peaks at a frequency  (1) equal to the resonant frequency (2) greater than the resonant frequency (3) less than the resonant frequency (4) equal to half the resonant frequency

asked Apr 29, 2018 in Network Analysis by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,530 questions

7,130 answers

135 comments

3,090 users

...