# When resistance element of a heater fuses and then we reconnect it ...

20 views
When resistance element of a heater fuses and then we reconnect it after removing a portion of it, the power of the heater will?

When resistance element of a heater fuses and then we reconnect it after removing a portion of it, the power of the heater will increase.

## Related questions

A star circuit has element of resistance R/2. The equivalent delta elements will be?

When an alternating current passes through an ohmic resistance the electrical power converted into heat is?

What is the relationship between power and resistance?

An electric heater draws 3.5 A from a 110 V source. The resistance of the heating element is approximately? A.385 ohms B.38.5ohms C.3.1 ohms D.31 ohms

For maximum transfer of power, internal resistance of the source should be?

When both the inductance and resistance of a coil are doubled the value of?

Two bulbs of 500 W and 200 W rated at 250 V will have resistance ratio as?

We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance R.A. voltmeter having a resistance of 1.2 kOhm is connected across 600 Ohm resistance and read 5v. The value of resistance R will be

The power consumed in a circuit element will be least when the phase difference between the current and voltage is?

Resistance of a material always decreases if?

A closed switch has a resistance of?

If a wire conductor of 0.2 ohm resistance is doubled in length, its resistance becomes?

The resistance of a few meters of wire conductor in closed electrical circuit is?

The resistance of a conductor varies inversely as?

What happens to the resistance of a wire when its length as well as the cross-sectional area are doubled? A) It doubles B) It becomes 4 times C) It becomes 2π times D) It remains the same

Temperature co-efficient of resistance is expressed in terms of?

International ohm is defined in terms of the resistance of?

The hot resistance of the bulb's filament is higher than its cold resistance because the temperature co-efficient of the filament is?

With rise in temperature the resistance of semi-conductors?

With rise in temperature the resistance of pure metals?

When current flows through heater coil it glows but supply wiring does not glow because?

An electric heater draws 3.5 A from a 110 V source. The resistance of the heating element is approximately equal to: A. 385Ω B. 38.5Ω C. 3.1Ω D. 31Ω

What amount of current will flow through resistance of 10 ohms when it is connected across a potential difference of 20 volts? A.30 amperes B.5 amperes C.10 amperes D.2 amperes

If resistance is 8 Ohm and current is 16 ampere then what will be the voltage and power?

When measuring insulation resistance of cables using d.c. source, the galvanometer used should be initially short circuited because  (A) Cables have a low value of capacitance which draws a high value of charging current (B) Cables have a low value of initial resistance (C) Cables have a high value of capacitance which draws a high value of charging current (D) Cables have a low value of capacitance and initial resistance

A single phase transformer has resistance and reactance of 0.2 pu and 0.6 pu respectively. Its pu voltage regulation at 0.8 pf lagging would he

A 200 V dc shunt motor is running at 1000 rpm and drawing a current of 10 A. Its armature winding resistance is 2 Ohm. It. is braked by plugging. The resistance to be connected in series with armature to restrict armature current to 10 A, is

What is the resistance of a coil which draws 10 A and dissipates 1520 W? A) 152 Ω B) 15.2 Ω C) 1.52 Ω D) None of these

A PMMC instrument has FSD of 100 μA and a coil resistance of 1 kΩ. To convert the instrument into an ammeter with full scale deflection of 100 mA, the required shunt resistance is (A) 1 Ω (B) 1.001 Ω (C) 0.5 Ω (D) 10 Ω

A moving coil meter has a resistance of 3 Ω and gives full scale deflection with 30 mA. To measure voltage up to 300 V, the external resistance to be connected in series with the instrument is (A) 9997 Ω (B) 10000 Ω (C) 997 Ω (D) 10003 Ω

If we change the excitation of synchronous machine will it affect on power factor?

What happens to the resistance when the current increases?

In a transformer the resistance between its primary and secondary should be?

Name two methods for measurement of low, medium and high resistance. Give one advantage and one limitation of V- I method.

State the use of shunt and series resistance used in extension of meter.

Define pinch off voltage and drain resistance of FET.

Identify the correct combination of respective Electric arc welding and Electric resistance welding methods :  (A) Butt welding and Seam welding  (B) Hydrogen shielding and Projection welding  (C) Seam welding and Coated electrode welding  (D) Coated electrode welding and Hydrogen shielding

When an antenna of input resistance 73 ohm is connected to a 50-ohm line and if the losses are ignored then its efficiency will be nearly   (A) 0.19 (B) 0.81 (C) 0.97 (D) 1.19

"Maximum power output is obtained from a network when the load resistance is equal to the output resistance of the network as seen from the terminals of the load". The above statement is associated with?

What is the mathematical relationship between resistance and conductance?

Parallel Reactance and Resistance Example 1

Problems on resistance and resistivity