# Kirchhoffs voltage law is related to?

10 views

Kirchhoffs voltage law is related to?

## Related questions

According to Kirchhoffs voltage law, the algebraic sum of all IR drops and e.m.f. in any closed loop of a network is always?

Kirchhoff's voltage law

Kirchhoff's voltage law applies to circuits with?

Kirchhoff's current law

Kirchhoffs current law is applicable to only?

Kirchhoff's current law states that?

Kirchhoff s law is not applicable to circuits with?

Kirchhoff s law is applicable to?

According to law of triangle of forces?

A network is said to be under resonance when the voltage and the current at the network input terminals are (A) in phase (B) out of phase (C) in phase quadrature (D) in phase, and have equal magnitudes

To determine the polarity of the voltage drop across a resistor, it is necessary to know?

The condition for the validity under Ohm's law is that?

What is the Lenz's law?

What is KCL and KVL law?

What is Coulomb's law ?

Which of the following theorems enables a number of voltage (or current) source to be combined directly into a single voltage (or current) source. (1) compensation theorem (2) reciprocity theorem (3) superposition theorem (4) Millman's theorem

Ohm's law formula

State and explain Lenz's law.

State and explain Ohm's law for magnetic circuit.

State Faraday's law of electromagnetic induction.

A DC voltage source is connected across a series RLC circuit. Under steady-state conditions, the applied DC voltage drops entirely across the

A network contains linear resistors and ideal voltage sources. If values of all the resistors are doubled then the voltage across each resistor will

The internal resistances of an ideal current source, and an ideal voltage source are, respectively, (A) 0, ∞ (B) ∞, ∞ (C) ∞, 0 (D) 0,0

An ideal voltage source has?

For a voltage source?

An ideal voltage source should have?

Kirchhoff's current law is applicable to 1. Closed loops in a circuit 2. Junction in a circuit 3. Magnetic circuits Which of the above is/are correct ?  (a) 1 only (b) 2 only (c) 3 only (d) 1, 2 and 3

An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak Envelope Power? A) 49.98 W B) 79.98 W C) 99.96 W D) 199.93 W

If 3000 kW power is to be transmitted over a distance of 30 km, the desirable transmission voltage will be.  (A) 11 kV (B) 33 kV (C) 66 kV (D) 132 kV

An amplifier has a voltage gain of 120. To reduce distortion, 10% negative feedback is employed. The gain of the amplifier with feedback is  (1) 141 (2) 92.3 (3) 9.23 (4) 1.41

A current controlled voltage source is equivalent to :  (A) series voltage feed -back amplifier (B) shunt current feed -back amplifier (C) shunt voltage feed -back amplifier (D) series current feed -back amplifier

An unshielded moving iron voltmeter is used to measure the voltage in an AC circuit. The stray DC magnetic field having a component along the axis will be  (1) unaffected (2) decreased (3) increased (4) either decreased or increased depending on the direction of the DC field

In which of the following waveforms is RMS voltage equal to the average voltage? A) Triangle wave B) Square wave C) Sine wave D) None of these

What happens to the voltage in the secondary when the frequency of the supply in the primary is decreased? A) It increases B) It decreases C) It remains the same D) Cannot say unless the actual percentage increase in the frequency is known

A circuit that binds the upper or lower extreme of a waveform to a fixed DC voltage level is called ______ A) DC voltage restorer B) Clamping circuit C) Both A and B D) None of these

A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum permissible stress in the dielectric is not to exceed 20 kV/mm. For economical size, the overall core diameter of the cable is (A) 28.2 mm (B) 26.4 mm (C) 24.4 mm (D) 22.0 mm

The voltage transformation ratio of a transformer is equal to the ratio of?

If a transformer is switched on to a voltage more than the rated voltage?

Why is it cheaper to transmit electrical energy at high voltage?

What equipment is used to measure voltage?

what is the minimum voltage required to turn on a diode ?