# Superposition theorem can be applied only to circuits having?

15 views

Superposition theorem can be applied only to circuits having?

Superposition theorem can be applied only to circuits having linear bilateral elements.

## Related questions

The superposition theorem requires as many circuits to be solved as there are?

State superposition theorem applied to D.C. circuits.

The superposition theorem is applicable to?

Can we apply the superposition theorem to AC circuit?

Which of the following statements is incorrect ? (A) Superposition theorem is useful for Linear and Non-linear circuit analysis when several sources are present in the circuit. (B) Thevenin's equivalent network consists of one voltage source in series with an impedance. (C) Norton's equivalent network consists of ... . (D) When both the load and source impedances are purely resistive, maximum power transfer is achieved under the condition : Load Resistance = Source Resistance

The concept on which Superposition theorem is based is?

State Superposition Theorem.

The superposition theorem is based on the concept of ?

Why superposition theorem is not valid for power?

Norton’s theorem states that a complex network connected to a load can be replaced with an equivalent impedance (A) in series with a current source (B) in parallel with a voltage source (C) in series with a voltage source (D) in parallel with a current source

In Thevenin's theorem, to find Z?

Application of Norton's theorem to a circuit yields?

In application of superposition theorem, one is required to solve as many circuits as there are  1. Nodes 2. Branches 3. Meshes 4. Sources

Millman's theorem yields equivalent  (1) Impedance or Resistance (3) Voltage source (2) Current source (4) Voltage or Current source

While calculating Rth in Thevenin's theorem and Norton equivalent?

Millman's theorem yields?

Can you apply Thevenin's theorem in an AC circuit?

Can we apply Norton's theorem in an AC circuit?

Superposition

Thevenin’s theorem can be applied to network containing : (A) Passive elements only (B) Active elements only (C) Linear elements only (D) All of these

Which of the following theorems can be applied to any network linear or non-linear, active or passive, time variant or time invariant?   (a) Thevenin Theorem (b) Norton Theorem (c) Telligen Theorem (d) Superposition Theorem

Maximum Power Transfer Theorem 1

Write the steps for finding the current through an element by Thevenin’s theorem.

State Thevenin’s Theorem.

State maximum power transfer theorem for DC circuit.

As per Shannon’s channel capacity theorem, if samples are transmitted in ‘T’ seconds over a noisy channel which is bandlimited to ‘B’ Hz. The number of samples ‘n’ is given by (symbols/notations carry their usual meaning) A) B/T B) T/B C) 2BT D) BT/2

Superposition theorem is not applicable to network containing: (1) Non linear element (2) Dependent voltage source (3) Dependent current source (4) Transformer.

In applying superposition theorem, to determine branch currents and voltages   (a) all current and voltage sources are shorted. (b) only current sources are open circuited. (c) only voltage sources are shorted. (d) voltage sources are shorted and current sources are open circuited.

The power delivered to a 3-phase load can be measured by the use of two wattmeters only when the  (a) load is unbalanced (b) load is balanced (c) three phase load is connected to the source through three wires (d) three phase load is connected to the source through four wires

The power delivered to a three-phase load can be measured by the use of 2 wattmeter only when the A. Load is balanced B. 3 -phase load is connected to the source through 3 wires C. Load is unbalanced D. 3 -phase load is connected to the source through 4 wires

If a variable can take only integer values from 0 to n, where n is a constant integer, then variable can be represented as a bit-field whose width is the integral part of (assume base 2)  (1) log(n) +1 (2) log(n + 1) + 1 (3) log(n – 1) + 1 (4) none of these

Which of the following instruments can be used to measure AC current only? (a) Permanent Magnet Type ammeter(b) Induction type ammeter (c) Moving iron voltmeter(d) Moving iron ammeter

Series or parallel resonant circuits can be used to create  A) Low pass filters B) Low pass and high pass filters C) Band—pass and band-stop filters D) All the above

To find current in a resistance connected in a network, Thevenin's theorem is used VTH = 20 V and RTH = 5 Ω. The current through the resistance: (1) is 4 A (2) is 4 A or less (3) is less than 4 A (4) May be 4 A or less or more than 4 A

Kirchhoffs current law is applicable to only?

Kirchhoff's voltage law applies to circuits with?

Kirchhoff s law is not applicable to circuits with?

Superposition theorem stays valid for a : -  a) LTI system b) Discrete system c) LT systems d) None of these

An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to secondary turn’s ratio 12:1. The peak inverse voltage is A) 8.62 V B) 12 V C) 19.17 V D) 27.11 V

Two sinusoidal signals having the same amplitude and frequency are applied to the X and Y inputs of a CRO. The observed Lissajous figure is straight line. The phase shift between the two signals would be (1) Zero (2) 90 degrees (3) Either zero or 180 degrees (4) Either 90 degrees or 270 degrees

A voltage signal 10 Sinwt is applied to the circuit with ideal diodes, as shown in figure. The maximum and minimum values of the output waveform vout of the circuit are respectively

A unit step voltage is applied at t = 0 to a series RL circuit with zero initial conditions  A) It is possible for the current to be oscillatory B) The voltage across the resistor at t = 0+ is zero C) The energy stored in the inductor in the steady state is zero D) Theresistor current eventually falls to zero

An SCR can only be turned off via it's   (A) cathode (B) anode (C) gates (D) none

The instantaneous power in ac circuits can be obtained by taking product of the instantaneous values of