# Application of Norton's theorem to a circuit yields?

46 views
Application of Norton's theorem to a circuit yields?

Application of Norton's theorem to a circuit yields equivalent current source and impedance in series.

## Related questions

While calculating Rth in Thevenin's theorem and Norton equivalent?

Application of Norton's theorem to a circuit yields : (A) Equivalent current source only (B) Equivalent voltage source only (C) Equivalent voltage source and impedance in series (D) Equivalent current source and impedance in parallel

Millman's theorem yields equivalent  (1) Impedance or Resistance (3) Voltage source (2) Current source (4) Voltage or Current source

Millman's theorem yields?

Norton’s theorem states that a complex network connected to a load can be replaced with an equivalent impedance (A) in series with a current source (B) in parallel with a voltage source (C) in series with a voltage source (D) in parallel with a current source

Can we apply Norton's theorem in an AC circuit?

Which of the following statements is incorrect ? (A) Superposition theorem is useful for Linear and Non-linear circuit analysis when several sources are present in the circuit. (B) Thevenin's equivalent network consists of one voltage source in series with an impedance. (C) Norton's equivalent network consists of ... . (D) When both the load and source impedances are purely resistive, maximum power transfer is achieved under the condition : Load Resistance = Source Resistance

The superposition theorem requires as many circuits to be solved as there are?

In Thevenin's theorem, to find Z?

The superposition theorem is applicable to?

Superposition theorem can be applied only to circuits having?

Can we apply the superposition theorem to AC circuit?

The concept on which Superposition theorem is based is?

State maximum power transfer theorem for DC circuit.

Can you apply Thevenin's theorem in an AC circuit?

State the application of phase sequence indicator; clip on ammeter, frequency meter & P.F. meter.

What is Amorphous metal? Give one application of this metal.

What is the application of thyristor?

What are the industrial application of electrolysis?

State superposition theorem applied to D.C. circuits.

What is op amp and its application?

Application Specific Instruction Set Processor (ASIP)

As per Shannon’s channel capacity theorem, if samples are transmitted in ‘T’ seconds over a noisy channel which is bandlimited to ‘B’ Hz. The number of samples ‘n’ is given by (symbols/notations carry their usual meaning) A) B/T B) T/B C) 2BT D) BT/2

The superposition theorem is based on the concept of ?

In application of superposition theorem, one is required to solve as many circuits as there are  1. Nodes 2. Branches 3. Meshes 4. Sources

Maximum Power Transfer Theorem 1

Write the steps for finding the current through an element by Thevenin’s theorem.

State Thevenin’s Theorem.

State Superposition Theorem.

Why superposition theorem is not valid for power?

Norton's equivalent of a circuit consists of a  1. Constant current generator with parallel impedance  2. Constant current generator in series with an infinite resistance  3. Constant current generator in parallel with high impedance  4. Constant current generator in series with low impedance

Norton's Theorem is a way to reduce a network to  (A) An equivalent circuit composed of a single current source, series resistance, and series load (B) An equivalent circuit composed of a single voltage source, parallel resistance, and parallel load (C) An equivalent circuit composed of a single voltage source, series resistance, and series load (D) An equivalent circuit composed of a single current source, parallel resistance, and parallel load

To find current in a resistance connected in a network, Thevenin's theorem is used VTH = 20 V and RTH = 5 Ω. The current through the resistance: (1) is 4 A (2) is 4 A or less (3) is less than 4 A (4) May be 4 A or less or more than 4 A

Time constant of a circuit is the time in seconds taken after the application of voltage to each?

A voltage signal 10 Sinwt is applied to the circuit with ideal diodes, as shown in figure. The maximum and minimum values of the output waveform vout of the circuit are respectively

A unit step voltage is applied at t = 0 to a series RL circuit with zero initial conditions  A) It is possible for the current to be oscillatory B) The voltage across the resistor at t = 0+ is zero C) The energy stored in the inductor in the steady state is zero D) Theresistor current eventually falls to zero

In a control system, moving a summing point right side to the block yields in  (A) Multiplication of the G(s) in the feedback path (B) Multiplication of the 1/G(s) in the feedback path (C) Addition of gain block (D) Subtraction of gain block

State the function of a contactor in a power circuit of locomotive. List different types of it and state one application of each.

In a series RLC circuit at resonance, the magnitude of the voltage developed across the capacitor  A) Is always zero B) Can never be greater than the input voltage C) Can be greater than the input voltage, however, it is 90° out of phase with the input voltage D) Can be greater than the input voltage, and is in phase with the input voltage

Which of the following are known as the short circuit parameters of a 2- port network? (A) Z- parameters. (B) H- parameters. (C) Y- parameters. (D) A,B,C,D, parameters.

A star circuit has element of resistance R/2. The equivalent delta elements will be?

An R-L series AC circuit has R = 10 ohm and XL = 10 ohm. It is connected to an AC voltage source, the phase angle between voltage and current is (a) 30° (b) 45° (c) 60° (d) 36.8°

A flasher circuit application is a : -  a) Safety blinkers for bicycles c) Street Light Control  b) Rides lighting d) Glow lamp