# The induced e.m.f. in the armature conductors of a d.c. motor is?

15 views
in DC motor

The induced e.m.f. in the armature conductors of a d.c. motor is?

The induced e.m.f. in the armature conductors of a d.c. motor is sinusoidal.

## Related questions

Which of the following quantity maintains the same direction whether a D.C. machine runs as a generator or as a motor a. Induced e.m.f. b. Armature Current c. Field Current d. Supply Current

The normal value of the armature resistance of a d.c. motor is?

The counter e.m.f. of a d.c. motor?

The induced emf in the armature of a lap -wound four -pole dc machine having 100 armature conductors rotating at 600 rpm and with 1 Wb flux per pole is  (1) 1000V (2) 100V (3) 600V (4) 10,000V

The e.m.f. induced in the armature of a shunt generator is 600 V. The armature resistance is 0.1 ohm. If the armature current is 200 A, the terminal voltage will be?

As there is no back e.m.f. at the instant of starting a D.C. motor, in order to prevent a heavy current from flowing though the armature circuit?

A d.c. shunt motor runs at no load speed of 1140 r.p.m. At full load armature reaction weakens the main flux by 5%. Whereas the armature circuit voltage drops by 10%. The full load speed of the motor is (a) 1200 r.p.m. (b) 1080 r.p.m. (c) 1040 r.p.m. (d) 1000 r.p.m.

The induced emf in the armature of a wave wound 4-pole d.c. machine having 100 armature conductors rotating at 600 r.p.m. and with a flux of 1 Wb per pole is (a) 1000 V (b) 2000 V (c) 200 V (d) 100 V

The e.m.f. induced in the primary of a transformer:  (A) is in phase with the flux (B) lags behind the flux by 90 degree (C) leads the flux by 90 degree (D) is in phase opposition to that of flux

These self inductance of a circuit is defined as twice the work done against the induced e.m.f. on establishing unit current in the coil. If the current to be established in the coil is doubled, the work done against the induced e.m.f. will be  1. Doubled  2. Halved  3. four times  4. Quarter times

Define the following terms as referred to battery. a) E.M.F b) Internal resistance c) Ah efficiency d) WAh efficiency

A step-down chopper, fed from a 120 volt DC source, operates a DC motor whose armature e.m.f. and armature resistance are 100 volt and 0.5Ω respectively. With the magnitude control ratio 0.6, the quadrant of operation DC motor is  (a) First (b) Second (c) Third (d) Fourth

The shaft torque of a d.c. motor is less than its armature torque because of .......... losses.

The mechanical power developed by the armature of a d.c. motor is equal to?

The function of steel wire in ACSR conductors is (A) To take care of surges. (B) To reduce corona. (C) To reduce inductance. (D) To provide additional mechanical strength

The skin effect in conductors is due to non uniform distribution of current in it and major portion of current is near the _______ of conductor.  (1) Surface (2) Center (3) Complete cross section area (4) Axis

The current drawn by a 120 - V d.c. motor of armature resistance 0.5 Ω and back e.m.f. 110 V is .......... ampere.

If a d.c. motor is disconnected from the source and armature circuit is short circuited through a suitable resistance, the process is called (a) regenerative breaking (b) rheostatic breaking (c) dynamic breaking (d) no breaking is possible

The voltage regulation of an alternator having 0.75 leading p.f. load, no-load induced e.m.f. of 2400V and rated terminal voltage of 3000V is —————————————  A) 20% B) —20% C) 150 D) -26.7

According to Fleming's right-hand rule for finding the direction of induced e.m.f., when middle finger points in the direction of induced e.m.f., forefinger will point in the direction of?

In a Synchronous motor, the magnitude of stator back e.m.f (Eb) depends on