# The position and velocity errors of a type-2 system are?

16 views
The position and velocity errors of a type-2 system are?

The position and velocity errors of a type-2 system are zero, constant.

## Related questions

For a feedback control system of type 2, the steady error for a rap input is  A) Infinite B) Constant C) Zero D) Indeterminate

Velocity error constant of a system is measured when the input to the system is unit _______ function.

The type 2 system has ______at the origin.

System 1 : The first column of the RH array consists of the terms 6,3,9,-2, and 4. System 2 : The first column of the RH array consists of the terms 3,6,9,2, and -4. The number of unstable poles for system1, and system 2, are respectively, (A) 1,1 (B) none, none (C) 2,2 (D) 2,1

. ICMP  (1) messages are encapsulated in an IP header (2) reports only on errors and problems (3) is integral part of TCP (4) is integral part of UDP

The pressure and velocity at the throat of a Venturi tube, measuring the flow of a liquid, are related to the upstream pressure and velocity, respectively, as follows: (A) Pressure is lower but velocity is higher (B) Pressure is higher but velocity is lower (C) Both pressure and velocity are lower (D) Pressure and velocity are identical

For a type three-control system the asymptote at lower frequency will have a slope  A) – 6 db per octave B) – 18 db per octave C) – 20 db per octave D) – 60 db per octave

The dc gain of the system represented by the transfer function G(s)=(s+6)/((s+2)(s+3)) is  A) 1 B) 2 C) 5 D) 6

What is the steady state error of type-0 system for ramp input?  A) ∞ B) A/K C) A/(1+K) D) 0

The steady state acceleration error of type-1 system is  A) Unity B) Infinity C) Constant D) Zero

Poles are real and negative and equal then the system is _____ damped system   (a) Undamped (b) Underdamped (c) Critically damped (d) Overdamped

When the initial conditions of a system are specified to be zero it implies that the system is?

State the following, 1) Position of head light 2) Supply voltage for flasher light 3) Colours used for marker light 4) Frequencies for engine horn.

The best method for determining the stability and transient response of a control system is (a) Bode Plot (b) Nyquist plot (c) Root locus (d) Routh-Hurwitz

The sensitivity of a closed loop system to gain changes and load disturbances depends upon (a) forward gain (b) loop gain (c) frequency (d) all the above

If a step function is applied to the input of a system and the output remains below a certain level for all the time, the system is?

A system has 14 poles and 2 zeros in its open -loop transfer function. The slope of its highest frequency asymptote in its magnitude plot is (a) - 40 dB/dec (b) - 240 dB/dec (c) + 40 dB/dec (d) + 240 dB/dec

In case of type-1 system steady state acceleration is?

The type 1 system has ______ at the origin.

The type 0 system has ______ at the origin.

A suspension type insulator has 2 units with self capacitance C and ground capacitance of 0.2 C. Each unit can withstand for a maximum voltage of 11 kV. Its string efficiency is  (A) 78% (B) 82% (C) 80% (D) 84%

Explain why LVDT gives a residual output at null position. State its 2 applications.

What are some examples of a closed loop system?

State the effects of errors in dynamometer type wattmeter due to i) pc- inductance ii) pc- capacitance iii) mutual inductance iv) Connection.

lf the poles of system are lying on the imaginary axis in s-plane, then the system will be

What are the advantages of open loop control system?

The three non -inductive loads of 5 kW, 3 kW and 2 kW are connected in a star network between R, Y and B phases and neutral. The line voltage is 400 V. The current in the neutral wire is nearly (a) 11 A (b) 14 A (c) 17 A (d) 21 A

What type of insulators are used whenever the conductors are dead ended and there is a change in the direction of transmission line?  (A) Shackle type (B) Strain type (C) Pin type (D) Suspension type

For a 2nd order servo system, the damping ratio δ = 0.5456 and undamped natural frequency is ωn = 31.6 rad/sec. The percent overshoot is  (a) 7.07 (b) 10.2 (c) 14.10 (d) 21.21

Which one most appropriate dynamic system? (1) y(n) + y(n – 1) + y(n + 1) (2) y(n) + y(n – 1) (3) y(n) = x(n) (4) y(n) + y(n – 1) + y(n + 3) = 0

Velocity of an electron (in km/S) starting at rest and travelling to a point 100 V above the starting potential is around  A) 3600 B) 4000 C) 5100 D) 6000

Consider a continuous-time system with input x(t) & output y(t) are related by y(t) = x (sin t). This system is (A) causal & linear (B) non-causal & linear (C) causal & non-linear (D) non-causal & non-linear

An absolutely integrable signal x(t) is known to have a pole at s = 2. Which one of the following is true ? (A) B, C and D are true (B) x(t) can be left-sided (C) x(t) can be right-sided (D) x(t) can be both-sided

In a PCM system the number of quantization level are 16 and the maximum signal frequency is 4 KHz the transmission bit rate is

The bandwidth and S/N of a communication system are 3MHz and 30dB respectively. The channel capacity (in Mbps) is around  A) 30 B) 300 C) 0.3 D) None of these

List any four errors in induction type energy meter. Give method of compensation for each.

Two light bulbs are connected in series across a 120 V battery. Bulb 1 uses 40 W of power and Bulb 2 uses 20 W of power. If bulb 1 alone is connected to the 120 V source, then it will consume (A) 90 W (B) 80 W (C) 60 W (D) 180 W

In a power generating station the Demand Factor and Load Factor are 0.5 and 0.2, respectively. If the connected load is 400 MW, the average demand is (A) 40 MW (B) 100 MW (C) 140 MW (D) 280 MW

For a system with derivative feedback, forward path transfer is G(s) = I / (s2 + s + 1) and feedback path transfer is H(s) = Ks. What is the value of K to obtain a critically-damped closed loop transient response.  (a) 0.5 (b) 0.707 (c) 1 (d) 1.414

A system is linear if and only if it satisfies

A plant is modeled as 1/(s(s+3)) with unity feedback control system and a cascade PI controller. How many state variables are required for state model description?   A) 1 B) 2 C) 3 D) 4

Find the area of the triangle whose vertices are 4,3 1,4 and 2,3 .

Analyze the differences of FOC and DTC. The switching frequency of FOC is 1.3 kHz and the average switching frequency of DTC is the same.