33 views
in Electrical Measurements and Instrumentation by

A 150 V moving iron voltmeter of accuracy class 1.0 reads 75 V when used in a circuit under a standard conditions. The maximum possible percentage error in the reading is:

1 Answer

0 votes
by

A 150 V moving iron voltmeter of accuracy class 1.0 reads 75 V when used in a circuit under a standard conditions. The maximum possible percentage error in the reading is:  2.0.

Related questions

1 answer 23 views

 In the case of an instrument reading of 8.3 V with a 0 to 150 voltmeter having a guaranteed accuracy of 1% full scale reading, the percentage limiting error is   (A) 1.810% (B) 0.181% (C)12.45% (D) 0.0018%

asked May 17, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 19 views

A 0 to 300V voltmeter has a guaranteed accuracy of 1% of full scale reading. The voltage measured by the instrument is 83V. The percentage limiting error is

asked Mar 28, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 51 views

A digital voltmeter has a read-out range from 0 to 9999 counts. When full scale reading is 9.999 V, the resolution of the instrument will be (a) 100 mV (b) 99 mV (c) 9 mV (d) 1 mV 

asked May 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 19 views

The full scale range of PMMC voltmeter is 100 V and its sensitivity is 1000 Ω/V. If the meter reads 50 V, the current through the voltmeter is (A) 0.05 mA (B) 0.5 mA (C) 5 mA (D) 50 mA 

asked Jun 4, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 19 views

The moving iron voltmeter indicates (a) the same value for dc and ac voltages. (b) lower values for ac voltage than for corresponding dc voltage. (c) higher value for ac voltage than for corresponding dc voltage. (d) none of these. 

asked May 25, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 58 views

An unshielded moving iron voltmeter is used to measure the voltage in an AC circuit. The stray DC magnetic field having a component along the axis will be  (1) unaffected (2) decreased (3) increased (4) either decreased or increased depending on the direction of the DC field

asked Apr 29, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 14 views

An average reading digital multimeter reads 10 V when fed with a triangular wave, symmetric about the time axis. For the same input the r.m.s. reading meter will read

asked May 25, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 11 views

Series resistance required to read 0-250 V with a moving coil instrument of internal resistance 2 ohm and full scale deflection of 50 mA is (a) 49998 Ω (b) 4998 Ω (c) 498 Ω (d) 49.8 Ω

asked May 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 40 views

When 7/0.029 V.I.R cable is carrying 20 A, a drop of 1 V occurs every 12 m. The voltage drop in a 100 m run of this cable when it is carrying 10 A is nearly  (a) 4.2 V (b) 3.2 V (c) 1.2 V (d) 0.42 V

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 87 views

A 0-10 A ammeter has a guaranteed accuracy of 1% of full scale deflection, the limiting error while reading 2.5 A will be (a) 1% (b) 2% (c) 4% (d) None of these 

asked May 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 27 views

When the voltage across a battery is measured using a D.C potentiometer, the reading shows 1.08 V. But when the same voltage is measured using a Permanent Magnet Moving Coil (PMMC) voltmeter, the voltmeter reading shows 0.99 V. If the resistance of the voltmeter is 1100 Ohm , the internal resistance of the battery, in Ohm , is (A) 150 (B) 100 (C) 50 (D) 200

asked Apr 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 24 views

A single phase 230 V/ 150 V , 1 kVA, 50 Hz transformer is supplied by 230 V AC supply. Find the full load primary and secondary current. 

asked Sep 1, 2018 by Quiz
0 answers 50 views

A moving coli ammeter has a fixed shunt of 0.02 Ω with a coil circuit resistance of R=1 kΩ and needs potential of 0.5 V across it for full scale deflection. Calculate the value of shunt to give full scale deflection when the total current is 10 A. (1) 0.05 Ω (2) 0.005 Ω (3) 0.5 Ω (4) 0.0005 Ω

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
0 answers 8 views

The sensitivity of a voltmeter using 0-5 mA meter movement is (a) 200 Ω/V (b) 150 Ω/V (c) 100 Ω/V (d) 50 Ω/V 

asked May 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 42 views

A dc voltmeter has a sensitivity of 1000 Ohm/V. When it measures half full scale in 100 V range, the current through the voltmeter is

asked Apr 23, 2018 in Electrical Engineering by Shimroz123
0 answers 12 views

Two voltmeters of same range, one moving iron type and other permanent magnet moving coil type, are connected in parallel for measuring a.c. supply voltage. If the reading of MI type is 300V, the reading of PMMC type will be (a) zero (b) higher-than M.I. type (c) lower than M.I. type (d) same

asked May 25, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 22 views

What is the charge on each capacitor when a 150 V is applied across two capacitors with values 5 μF and 10 μF, connected in series? A) 500 μC B) 0.5 μC C) 0.5 C D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 43 views

Consider the following statements with regard to Moving Iron (MI) instruments :  1. These instruments possess high operating torque.  2. These instruments can be used in ac and dc circuits.  3. Power consumption in these instruments is lower for low voltage range.  Which of the above statements are correct ?  (a) 1 and 2 only (b) 1 and 3 only (c) 2 and 3 only (d) 1, 2 and 3

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

A moving coil instrument of resistance 5 Ohm requires a potential difference of 75 mV to give a full scale deflection. The value of shunt resistance needed to give a full scale deflection at 30 A is

asked Apr 23, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

A moving coil instrument has a resistance of 10 W and gives full scale deflection when carrying a current of 50 mA. To measure current upto 100 A, we will have to connect • 10 W resistance in series • 10 W resistance in parallel • 10/1999 W resistance in series • 10/1999 W resistance in parallel

asked May 13, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 26 views

Horizontally mounted moving iron instruments use   (a) Eddy current damping (b) Electromagnetic damping (c) Fluid friction damping (d) Air friction damping

asked May 13, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 195 views
1 answer 15 views

The e.m.f. induced in the armature of a shunt generator is 600 V. The armature resistance is 0.1 ohm. If the armature current is 200 A, the terminal voltage will be?

asked Mar 21, 2018 in DC generator by Shimroz123
1 answer 43 views

For a short transmission line with r/x ratio of is 1.0, the regulation will be zero when the load power factor is

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

A 10A DC Ammeter has a resistance of 0.1 Ω is to be extended to 50 A, the required shunt wire is A) Manganin wire of 20 m Ω B) Constantan wire of 20 m Ω C) Manganin wire of 25 m Ω D) Constantan wire of 25 m Ω

asked Jun 4, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 14 views

The bridge most suited for measurement of a four-terminal resistance in the range of 0.001 Ohm to 0.1 Ohm (A) Wien’s bridge (B) Kelvin double bridge (C) Maxwell’s bridge (D) Shering Bridge

asked Apr 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
2 answers 75 views

If an incandescent lamp of 80 ohms resistance takes a current of 0.75 ampere, what voltage is required to light it? A.45 volts B.60 volts c.23 volts D.None of these

asked May 15, 2018 in Basic concepts by Zeeshan
1 answer 20 views

A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V, variable frequency supply. The current drawn by the circuit is found to be minimum when the supply frequency is 1 kHz. The approximate values of Q-factor and bandwidth are, respectively (A) 40, 400 Hz (B) 10, 100 Hz (C) 20, 50 Hz (D) 50, 20 Hz

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
0 answers 33 views

A carrier signal of 600 V rms with 75% amplitude modulation is applied to 75 ohm antenna. The total side band power (in watts) is  A) 4800 B) 450 C) 950 D) 1350 

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 31 views

An ammeter of 0-25 A range has a guaranteed accuracy of 1% of full scale reading. The current measured 5 A The limiting error is  A) 2% B) 2.5% C) 4% D) 5%

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 18 views

When the SCR conducts, the forward voltage drop will   (a) 0.7 V at all load current (b) 2 to 2.5 V at all load current (c) increases slightly with load current (d) remains constant with load current 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 112 views

The time/div and voltage/div axes of an oscilloscope have been erased. When a 1 kHz, 5V p-p square wave calibration pulse is connected to channel 1 ofthe scope the waveform observed on the screen is as shown in the upper trace of the figure. An unknown signal is connected to channel 2 (lower trace) ofthe scope. If the time/div and V/div on both channels are the same, the amplitude (pp) and period of the unknown signal are respectively.

asked May 20, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 9 views

 When A = 0., B = 0, C = 1 then in two input logic gate we get gate  (A) XOR gate (B) AND gate (C) NAND gate (D) NOR gate

asked May 17, 2018 in Digital Electronics by Shimroz123
0 answers 21 views

The emf induced in a coil is 1 volt when current in it changes from 0 to 100 mA in time 10mS. Its inductance (in mH) value is  A) 10 B) 50 C) 100 D) 1000

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 17 views

 A 0 -10 mAPMMC ammeter reads 5 mA in a circuit; its bottom control spring snaps out suddenly the meter will now read:- a) 5 mA b) 10 mA c) 2.5 mA d). 0

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 30 views

The Q factor of a coil at resonant frequency 1.5 MHz of an RLC series circuit is 150. The Bandwidth is : - a) 225 MHz b) 1.06 MHz c) 10 KHz d) 10 MHz

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 25 views

The output of logic gate is '1' when all its inputs are at logic '0' The gate is (A) NAND/EX-OR (B) NOR/EX-OR (C) AND/EX-NOR (D) NOR/EX-NOR

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 30 views

The coefficient of coupling between two coils is 0.45. The first coil has an inductance of 75 mH and the second coil has an inductance of 105 mH. What is the mutual inductance between the coils?  (1) 3.54 mH (2) 7.88 mH (3) 39.9 mH (4) 189.3 mH

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 16 views

The voltage regulation of an alternator having 0.75 leading p.f. load, no-load induced e.m.f. of 2400V and rated terminal voltage of 3000V is —————————————  A) 20% B) —20% C) 150 D) -26.7

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 37 views

A 150 kW electric motor has an efficiency of 92 %, when it operates at full load. Calculate the losses in the machine.  (A) 92 kW (B) 150 kW (C) 163 kW (D) 13 kW 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 28 views

Assume that the n-channel MOSFET shown in figure is ideal and that its threshold voltage is +1 .0 V. The voltage Vab between nodes a and b is A)5V B)2V C)1V D)0V

asked May 20, 2018 in MOSFET by Shimroz123
0 answers 23 views

A 1mA D' Arsonval movement has resistance of 100 Ω. It is to be converted to a 10 V voltmeter. The value of multiplier resistance is  (A) 999 Ω (B) 9999 Ω (C) 9900 Ω (D) 990 Ω 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...