The damping torque must operate only when the moving system of the indicating instrument is:

42 views

The damping torque must operate only when the moving system of the indicating instrument is: Actually moving

Related questions

The moving system of an indicating type of electrical instrument is subjected to (a) a deflecting torque (b) a controlling torque (c) a damping torque (d) All of the above

Eddy current damping cannot be used for moving iron instrument because

The effect of stray magnetic fields on the actuating torque of a portable instrument is maximum when the operating field of the instrument and the stray fields are  A) Perpendicular B) Parallel C) Inclined at 60" D) Inclined at 30°

A moving coil instrument has a resistance of 10 W and gives full scale deflection when carrying a current of 50 mA. To measure current upto 100 A, we will have to connect • 10 W resistance in series • 10 W resistance in parallel • 10/1999 W resistance in series • 10/1999 W resistance in parallel

For a desirable transient response of a second order system, the damping ratio must be between (a) 0.4 and 0.8 (b) 0.8 and 1.0 (c) 0.3 and 0.5 (d) 0.2 and 0.4

The deflecting torque of a moving coil instrument depends on (a) supply frequency (c) flux in the coil (b) inverse of area of coil (d) square of the voltage

In a PMMC instrument, the damping provided is :  (A) air damping (C) eddy current damping (B) fluid damping (D) magnetic damping using a magnet

Ideally, the damping torque should be  (1) Proportional to velocity of the moving system and operating current.  (2) Proportional to the velocity of the moving system but independent of operating current.  (3) Independent of the velocity of the moving system and proportional to the operating current.  (4) Independent of the velocity of the moving system and operating current.

Series resistance required to read 0-250 V with a moving coil instrument of internal resistance 2 ohm and full scale deflection of 50 mA is (a) 49998 Ω (b) 4998 Ω (c) 498 Ω (d) 49.8 Ω

In a second order system the value of resonant peak will be unity when the damping ratio has a value of  A) Zero B) Unity C) 0.707 D) 0.414

A motor load system is stable when the slope of the torque speed characteristics of the motor is (a) higher than the slope of the torque speed characteristics of the load (b) lower than the slope of the torque speed characteristics of the load (c) zero (d) none of the above

A 150 V moving iron voltmeter of accuracy class 1.0 reads 75 V when used in a circuit under a standard conditions. The maximum possible percentage error in the reading is:

For controlling the vibration of the disc of ac energy meter, damping torque is produced by

The force required to move the pointer in an indicating instruments is

A control system having unit damping factor will give  (1) Oscillatory response (2) Undamped response (3) Critically damped response (4) No response

Eddy current damping is normally used in the instruments of (a) Induction type (b) Moving iron type (c) Permanent magnet moving coil type (d) Nothing can be said

The characteristic equation of a simple servo system is s2+6s+25=0. Damping factor of the system is: A) 3.2 B) 2.4 C) 1.8 D) 2.9

Given a unity feedback system with G(s)=k/s (s+4), the value of k for damping ratio of 0.5 is

The damping factor of a particular system is unity, the system response will be

In the time response analysis of control system, Damping Ratio is given by - a) Actual damping / Critical damping b) Critical damping /Actual damping c) ( Sum of the Actual damping and critical damping) /Actual damping d)( Difference of the Actual damping and critical damping) / critical damping

A system is causal if the output of any time depends only on   (A) Values of input in the past and in the future (B) Values of input at that time and in the past (C) Values of input at that time and in the future (D) none

Damping torque used in energy meter is : - a) Electrostatic b) Electro magnetic c) Eddy Current d) None

List the different methods to produce damping torque.

State the function of controlling torque in electrical measuring instrument.

In a portable instrument, the controlling torque is provided by  A) Spring B) gravity C) eddy currents D) all of the above

In moving iron instruments, eddy current damping cannot be used as  (a) They have a strong operating magnetic, field (b) They are not normally used in vertical position (c) They need a large damping force, which can only be provided by air friction (d) The introduction of a permanent magnet required for eddy current damping would distort the existing weak operating magnetic field

A moving coil instrument of resistance 5 Ohm requires a potential difference of 75 mV to give a full scale deflection. The value of shunt resistance needed to give a full scale deflection at 30 A is

A Hurwitz polynomial D(s) must satisfy two conditions. One is the polynomial is real when s is real. What is the other condition ?