# In integrated circuit electronics the basic universal gate is

276 views

In integrated circuit electronics the basic universal gate is AND gate.

## Related questions

basic gate drive circuit of GTO

Which of the following gate is called universal gate?  (A) AND (B) NOT (C) NOR (D) EX-OR

Read the following statements: i. Gate is a combinational logic. ii. JK Flip-flop in toggle mode is not combinational logic. iii. MSJK Flip-flop suffers from race-around. iv. Counters are sequential circuits. Which choice is correct? (A) i, ii (B) i, ii, iv (C) ii, iii, iv (D) i, ii, iii

The basic logic gate whose output is the complement of the input is the: - a) OR gate b) AND gate c) inverter d) comparator

The complete set of only those Logic Gates designated as Universal Gates is  (A) NOT, OR and AND Gates (B) XNOR, NOR and NAND Gates (C) NOR and NAND Gates (D) XOR, NOR and NAND Gates

1.Determine the permeability of magnetic material by plotting its BH curve 2. Measure voltage, current and power in 1-phase circuit with resistive load. 3. Measure voltage, current and power in R-L series circuit. 4.Determine the transformation ratio (K) of 1-phase transformer. 5.Connect single phase transformer and measure input and output quantities. 6.Make Star and Delta connection in induction motor starters and measure the line and phase values.

What is drive circuit in power electronics?

The structure of a multi -layered integrated circuit is determined by (a) Removing successive layers of the circuit. (b) The intensity of backscattered or secondary electrons is detected by first or second detector. (c) Surface of the integrated circuit is a flat layer of semiconductor substrate material having implanted doped areas, the surface is covered with a metallisation layer providing a Schottky barrier. (d) All 3 of above.

The output of an exclusive–NOR gate is 1. Which input combination is correct? (1) A = 1, B = 0 (2) A = 0, B = 1 (3) A = 0, B = 0 (4) None of these

The gate whose output is LOW, if and only if all the inputs are HIGH, is

The o/p of a 2 - input OR gate is 1 when its   1. both inputs are 1 2. both inputs are 0 3.either input is 1 4. either input is 0

What is the purpose of a NAND gate?

When A = 0., B = 0, C = 1 then in two input logic gate we get gate  (A) XOR gate (B) AND gate (C) NAND gate (D) NOR gate

what is integrated circuit ?

list the product names which have Integrated circuit.

For the circuit shown in figure, the Boolean expression for the output y in terms of inputs P, Q, R and S is

A NOR gate is equivalent to a bubbled AND gate. This statement is an outcome of: (1) De Morgan’s Law (2) Involution Law (3) Law of Absorption (4) Idempotent Law

Output of NAND gate is 0. for three inputs when:

What is an inverter gate?

A resistor connected across the gate and cathode of an SCR in a circuit increases its (A) dv/dt rating (B) Holding current (C) Noise Immunity (D) Turn-off time

For a NAND gate, when one or more inputs are low then the output will be A) Low B) High C) Alternately high and low D) High or low depending on relative magnitude of inputs

The output of a 2-input NAND gate with high at both the inputs will be • High • Low • High & low • None of the above.

What does the AND gate do?

For fabricating cost effective high valued integrated resistors in IC, the method used is  A) Diffused resistor B) Epitaxial resistor C) Pinched resistor D) Thin film resistor

How many minimum number of NOR gates are required to realize a two-input X-OR gate?

The two basic components of a Thevenin equivalent ac circuit are the equivalent voltage source and the equivalent: A. Series impedance B. Series resistance C. Parallel impedance D. Parallel resistance

A switch tail ring counter is made by using a single D-FF. The resulting circuit is (A) T-FF (B) D-FF (C) SR-FF (D) JK-FF

Describe the gate circuit for a single phase full converter.

What is meant by feedback in electronics?