15 views
in Electrical Engineering by
A chopper operating at a fixed frequency is feeding an R-L load. As they duty ratio of the chopper is increased from 25% to 75%, the ripple in the load current.

1 Answer

0 votes
by

Remains constant.

Related questions

1 answer 39 views

A dc chopper is fed from a constant voltage mains the duty ratio of chopper is progressively increased while the chopper feeds an RL load. The per unit current ripple would  (1) increase progressively  (2) decrease progressively  (3) decrease to a minimum value at α = 0.5 and then increase  (4) increase to a maximum value at α = 0.5 and then decrease

asked Apr 30, 2018 in Power Electronics by Shimroz123
2 answers 21 views

Ripple in output current of a step-down chopper feeding RLE load is maximum, when duty cycle is equal to:  (1) 1 (2) 0.5 (3) 0.75 (4) 0.33

asked May 22, 2018 in Electronics Engineering by Shimroz123
0 answers 20 views

The duty ratio of a step-up chopper with an output voltage of 200 V from a 80 V dc source, is (A) 0.4 (B) 0.5 (C ) 0.6 (D) 1.5 

asked Jun 4, 2018 in Power Electronics by Shimroz123
1 answer 38 views

In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is (A) sinusoidal current (B) constant dc current (C) continuous rectangular pulses (D) alternating rectangular pulses

asked Apr 28, 2018 in Power Electronics by Shimroz123
0 answers 90 views

 When The dc converter in figure shown has a resistance load of R = 10 Ω and the input voltage is Vs 220 V the converter switch remains on, its voltage drop is Vo -2 V. The chopping frequency is fI K sW Vs If the duty cycle is 50%, determine: (a) the average output voltage V (b) the RMS output voltage Vo (c) the converter efficiency (d) the effective input resistance of the converter

asked Apr 26 by Hussein
0 answers 21 views

A large transformer operating at no load draws an exciting current Io of 5A, when the primary is connected to a 120 V, 60 Hz source. From a wattmeter test, it is known that iron losses are equal to 180 W. Calculate the reactive power absorbed by the core.  (A) 600 var (B) 572 var (C) 180 var (D) 360 var 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

A transmission line is operating with a Phase shift of 80° between two ends. If the load is suddenly increased A) The phase displacement will increase B) The phase displacement will decrease C) The phase displacement will not change D) The surge impedance will increase

asked May 24, 2018 in Electrical Engineering by Shimroz123
1 answer 24 views

At ______ frequencies the parallel R-L circuit behaves as purely resistive.

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 22 views

A series R-L-C Circuit has a resonant frequency of 1000 Hz. If the values of R, L and C are doubled, the new resonant frequency is

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 43 views

For a short transmission line with r/x ratio of is 1.0, the regulation will be zero when the load power factor is

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
0 answers 21 views

A synchronous motor is delivering 80% of its rated output and is operating at UPF. If its excitation is increased, then  (1) the output delivered gets increased (2) its pf becomes lagging (3) the output delivered gets decreased (4) its pf becomes leading

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 34 views

An 8 pole wound rotor induction motor operating on 60 Hz supply is driven at 1800 r.p.m. by a prime mover in the opposite direction of revolving magnetic field. The frequency of the rotor current is (a) 30 Hz (b) 60 Hz (c) 120 Hz (d) 180 Hz 

asked May 25, 2018 in Induction Machine by Shimroz123
1 answer 27 views

In a synchronous generator if the excitation increased from a low value to normal value, with a fixed load  (A) The armature current increases and the power factor decreases  (B) The armature current decreases and the power factor also decreases  (C) The armature current decreases and the power factor increases but is lagging  (D) The armature current decreases and the power factor increases and is leading

asked Apr 29, 2018 in Electrical Machine by Shimroz123
1 answer 17 views

In R-L-C series resonant circuit magnitude of resonance frequency can be changed by changing the value of?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
0 answers 17 views

Impulse response of an R–L circuit is a : (A) Rising exponential function (B) Decaying exponential function (C) Step function (D) Parabolic function

asked Mar 31, 2018 in Electrical Engineering by Shimroz123
1 answer 223 views

Total instantaneous power supplied by a 3-phase ac supply to a balanced R-L load is

asked Apr 28, 2018 in Electrical Engineering by Shimroz123
1 answer 48 views

A step voltage E is applied to a series R-L circuit. The rate of change of current is maximum at t = _:  (1) Zero (2) Infinity (3) L/R (4) R/L 

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 14 views

The values of L and C for a low pass filter with cut off frequency of 2.5 KHz and operating with a terminated load resistance of 450 Ohm are given by  (a) 57.3 mH; 0.283 μF (b) 28.66 μH; 0.14 μF (c) 114.64 mH; 0.566 mF (d) 50.23 mH; 0.632 mF

asked May 16, 2018 in Electronics Engineering by Shimroz123
1 answer 41 views

A 3 -phase, fully controlled, converter is feeding power into a DC load at a constant current of 150 A, the rms value of the current flowing through each thyristor of the converter is

asked Apr 29, 2018 in Power Electronics by Shimroz123
1 answer 32 views

A series RLC circuit has a resonant frequency of 1 KHz and a quality factor Q = 100. If each of the R,L and C is doubled from its original value, the new Q of the circuit is:  (1) 25 (2) 50 (3) 100 (4) 200

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 28 views

 A transformer has maximum efficiency at 3/4 full load. The ratio of its iron losses and full load copper loss is : -  a) 16/9 b) 4 / 3 c) 3/4 d) 9 /16

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
2 answers 36 views

The power factor at resonance in R-L- C parallel circuit is?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
0 answers 27 views

An SMPS operating at 20 kHz to 100 kHz range uses as the main switching element : (A) Thyristor (B) MOSFET (C) Triac (D) UJT

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 17 views

A three-phase star -connected load is operating at a power factor angle ϕ  with ϕ being the angle between

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 19 views

In a series L-C circuit at the resonant frequency the?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

A synchronous generator is feeding a zero power factor (lagging) load at rated current. The armature reaction is  (A) magnetizing (B) demagnetizing (C) cross-magnetizing (D) ineffective

asked May 17, 2018 in Synchronous machine by Shimroz123
1 answer 20 views

The r.m.s. value of a sinusoidal A.C. current is equal to its value at an angle of______degrees.

asked Mar 24, 2018 in Electrical Engineering by Shimroz123
2 answers 24 views

Magnitude of current at resonance in R-L-C circuit?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
0 answers 38 views

A balanced Delta connected load supplied with 440 V 50 Hz three phase AC supply has R=10 Ohm and L=0.6 mH in is each arm. Calculate line and phase current, active power.

asked Aug 12, 2018 in Basic electrical and electronics engineering by Quiz
0 answers 27 views

A series R-L circuit is suddenly connected to d.c. voltage source of V volts. The current in this series circuit, just after the switch is closed, is equal to (1) Zero (2) V/L (3) V/C (4) V.L/C 

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
0 answers 43 views

A thyristor is triggered by a pulse train of 5 kHz. The duty ratio is 0.4. If the allowable average power is 100 W, the maximum allowable gate drive power will be 

asked May 25, 2018 in Power Electronics by Shimroz123
1 answer 73 views

The X:R ratio of 220 kV line as compared to 400 kV line is?

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 24 views

A single-phase transformer has a turns ratio of 1 :2 and is connected to a purely resistive load as shown in the figure. The magnetizing current drawn is 1A, and the secondary current is 1A. Ifcore losses and leakage reactances are neglected, the primary current is  A)1.41A B)2A C) 2.24A D)3A

asked May 20, 2018 in Transformer by Shimroz123
1 answer 21 views

A 3~phase synchronous motor, connected to infinite bus, is operating at no load at normal excitation. The field excitation of the motor is first decreased to zero and then increased in the reverse direction. The armature current of the synchronous motor will:  (1) Remain constant. (2) First decrease and then increase, (3) Increases continuously (4) First increase and then decreased

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

In an AC circuit, the voltage across R, L and C are 30 V, 60 V and 20 V respectively. The applied voltage is (A) 70 V (B) 50 V (C) 60 V (D) 100 V

asked May 12, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

Two synchronous generators operating in parallel supply a common load of 2.5 MW. The frequency-power characteristics have a common slope of 1 MW/Hz and the no-load frequencies of the generators are 51.5 Hz and 51.0 Hz, respectively. Then the system frequency is (A) 50 Hz (B) 51 Hz (C) 51.25 Hz (D) 51.5 Hz

asked Apr 28, 2018 in Electrical Machine by Shimroz123
0 answers 49 views

A single phase, half-wave, controlled rectifier has 400 sin (314 t) as the input voltage and R as the load. For a firing angle of 60° for the SCR, the average output voltage is   (a) 240/π (b) 400/π (c) 300/π (d) 200/π 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 19 views

The output power of a filter is 100 mW, when the signal frequency is 6 kHz. When the frequency is increased to 25 kHz, the output power falls to 50 mW. What is the dB change in power ? (a) -3 dB (b) -5 dB (c) -7 dB (d) -2 dB

asked Apr 23, 2018 in Electrical Engineering by Zeeshan
0 answers 50 views

A moving coli ammeter has a fixed shunt of 0.02 Ω with a coil circuit resistance of R=1 kΩ and needs potential of 0.5 V across it for full scale deflection. Calculate the value of shunt to give full scale deflection when the total current is 10 A. (1) 0.05 Ω (2) 0.005 Ω (3) 0.5 Ω (4) 0.0005 Ω

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
0 answers 18 views

A parallel combination of capacitance C and resistance R is connected in series with inductance L and small resistance r. Under what condition will the circuit be non-reactive?  (A) C=LR (B) C=LR2 (C) C=L/R2 (D) C=L/R

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 25 views

If resistance is 20 Q. and inductance is 27 in a R-L series circuit, then time constant of this circuit will be?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 22 views

What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively? A) 320 V B) 448 V C) 64 V D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 30 views

In a loss-free R-L-C circuit the transient current is?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 26 views

An iron cored inductance coil can be modelled, over a normal operating range of networks ,as A) non-Linear bilateral element B) linear bilateral element C) linear time varying element D) non-linear time invariant element

asked May 24, 2018 in Electrical Engineering by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...