21 views
in Electrical Engineering by
which of the following induction motor will have the least shaft diameter?

(a) 20 HP, 2880 rpm

(b) 20 HP, 1440 rpm

(c) 20 HP, 960 rpm

(d) 20 HP, 730 rpm

1 Answer

0 votes
by

20 HP, 2880 rpm

Related questions

0 answers 21 views

The diameter of the rotor shaft for an electric motor depends on which of the following (1) rpm only (2) hp only (3) hp and rpm (4) hp, rpm and Power factor 

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
2 answers 34 views

Which of the following plants will take least time in starting from cold conditions to full-load operation? A) Nuclear power plant B) Steam power plant C) Hydro-electric power plant D) Gas turbine plant

asked Jun 4, 2018 in Electric Power Generation by Shimroz123
1 answer 29 views

A 3 phase, 400 volts, 50 Hz, 100 kW, 4 pole squirrel cage induction motor with a rated slip of 2% will have a rotor speed of: (A) 1500 rpm (B) 1470 rpm (C) 1530 rpm (D) 1570 rpm

asked Apr 11, 2018 in Computer Engineering by Shimroz123
1 answer 13 views

 In which of the following power plants the availability of power is least reliable? A) Solar power plant B) Wind energy C) Tidal power plant D) Geothermal power plant

asked Jun 17, 2018 in Electrical Engineering by Shimroz123
1 answer 19 views

Which of the following is the least expensive protection for over current in low voltage system?  (A) Rewireable fuse (B) Isolator (C) Oil Circuit breaker (D) Air break circuit breaker

asked May 8, 2018 in Electrical Engineering by Zeeshan
0 answers 17 views

Which of the following bulbs operates on least power ?  (1) GLS bulb (2) Torch bulb (3) Neon bulb (4) Night bulb

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

A shaded pole induction motor does not have the advantage of   (a) Rugged construction (b) Low initial as well as maintenance cost (c) High starting torque (d) Comparatively small starting current 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

Which statement out of the following is a wrong statement with regard to Induction motor? A) Auto-transformer starter is costlier to “direct on line” (DOL) starter B) DOL starter is used for motors up to 5 horse power only C) Auto transformer starter is used for motors up to 20 horse power only D) Star delta starter connects the motor first in delta at the time of starting then in star for running

asked Jun 17, 2018 in Induction Machine by Shimroz123
1 answer 13 views

For a single phase capacitor start induction motor, which of the following statements is valid?  A) The capacitor is used for power factor improvement B) The direction of rotation can be changed by reversing the main winding terminals C) The direction of rotation cannot be changed D) The direction of rotation can be changed by interchanging the supply terminals

asked May 17, 2018 in Induction Machine by Shimroz123
1 answer 18 views

Which of the following amplifier has the least distortion. • Class E • Class D • Class C • Class A

asked May 14, 2018 in Amplifier by Shimroz123
0 answers 20 views

If the supply frequency of a 3-phase induction motor is ‘f’, then frequency of rotor emf at motor slip ‘s’ will be   (a) sf (b) (1 – s)f (c) f/s (d) None of these 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
0 answers 44 views

Reduction in supply voltage by 10% will change the torque of an induction motor by   (a) 38% (b) 19% (c) 9.5% (d) No change 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
2 answers 58 views

The synchronous speed of an 8 pole induction motor supplied power from a 50 Hz source will be ?

asked Dec 31, 2017 in Electrical Engineering by Quiz
1 answer 28 views

Which motor have more efficiency, synchronous motor or induction motor?

asked Mar 18, 2018 in Synchronous machine by Shimroz123
1 answer 25 views

 Which one of the following does not have an effect on corona ?  (a) Spacing between conductors (b) Conductor size (c) Line voltage (d) Length of conductor

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 10 views

Which of the following can have positive or negative charge? A. Electron B. Iron C. Hole D. Neutron. 

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 24 views

A permanent magnet stepper motor with 8 poles in stator and 6 poles in rotor will have a step angle of (a) 7.5° (b) 15° (c) 30° (d) 60°

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
0 answers 27 views

Which of the following statements is CORRECT?  (A) A grid-connected induction generator always supplies lagging reactive power to the bus. (B) An overexcited synchronous motor draws current at a lagging power factor. (C) An under excited synchronous generator connected to an infinite bus works at a leading power factor. (D) The load angle of a synchronous machine is the angle between the excitation voltage and the load current.

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

lf the wire which is vertical to this page has electron flow downwards the conductor will have

asked Apr 26, 2018 in Electrical Engineering by Shimroz123
1 answer 9 views

Which of the following will happen if a voltmeter is connected like an ammeter in series to the load ? (A) There will be almost no current in the circuit. (B) The meter will burn. (C) The measurement will be trio high. (D)  A very high current will flow.

asked May 12, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

Which of the following connection of transformers will give highest value of secondary voltage ? (A) Delta primary delta secondary (B) Delta primary star secondary (C) Star primary star secondary (D) Star primary delta secondary

asked May 8, 2018 in Electrical Engineering by Shimroz123
0 answers 22 views

Which of the following will not cause permanent damage of an SCR ? (A) High current (B) High rate of rise of current (C) High temperature rise (D) High rate of rise of voltage

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 9 views

Which of the following alternatives will be cheaper (1) A 100 h.p AC, 3-phase motor (2) Four motors of 25 h.p each (3) Five motors of 20 h.p each (4) 10 motors of 10 h.p each  

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
0 answers 14 views

A change of 5% in supply voltage to an induction motor will produce a change of approximately (a) 5% in the rotor torque (b) 7.5% in the rotor torque (c) 10% in the rotor torque (d) 25% in the rotor torque

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 12 views

A three phase induction motor is driving full -load torque which is independent of speed. If the line voltage drops to 90% of the rated value, % increase in motor copper losses  (a) 23% (b) -18% (c) 123% (d) None of these

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

Why does induction motor have high starting current?

asked Mar 15, 2018 in Electrical Engineering by Quiz
1 answer 75 views

The power consumed in a circuit element will be least when the phase difference between the current and voltage is?

asked Mar 24, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

The shaft torque of a d.c. motor is less than its armature torque because of .......... losses.

asked Mar 26, 2018 in DC motor by Shimroz123
1 answer 10 views

Which of the following motor has squirrel cage winding on the stator: (1) 3 phase squirrel cage induction motor (2) Single phase squirrel cage pump motor (3) Single phase ceiling fan induction motor (4) Single phase table fan induction motor 

asked May 29, 2018 in Electrical Engineering by Shimroz123
0 answers 15 views

 Which of the following motor would suit applications where constant speed is absolutely essential ? (A) Brushless dc motor (B) Disk motor (C) Permanent -magnet synchronous motor (D) Stepper motor

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 27 views

For a stepper motor which of the following torque has the highest numerical value ? (A) Detent torque (B) Pull -in torque (C) Pullout torque (D) Holding torque

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 19 views

While selecting motor for an A.C which of the following characteristics is of great importance (1) Type of bearings (2) Type of enclosure (3) Noise (4) Arrangement for power transmission  

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
0 answers 19 views

For blowers which of the following motor is preferred? (1) D.C. series motor (2) D.C. shunt motor (3) Squirrel cage induction motor (4) Wound rotor induction motor  

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

The power factor of an induction motor under no load conditions will be close to (A) 0.2 lagging (B) 0.2 leading (C) 0.5 lagging (D) Unity

asked May 12, 2018 in Induction Machine by Shimroz123
1 answer 20 views

A change of 4% in the supply voltage to an induction motor will produce a change of approximately

asked May 8, 2018 in Electrical Machine by Shimroz123
1 answer 41 views

In an induction motor if the flux density is reduced to one-half, of its normal value then the torque will  (1) reduce to one-half (2) reduce to one-fourth (3) remain unchanged (4) increase four times

asked May 1, 2018 in Electrical Machine by Shimroz123
1 answer 16 views

The number of poles in a phase induction motor at 50 Hz and running at 1500 rpm will be?

asked Mar 26, 2018 in Induction Machine by Shimroz123
1 answer 64 views

A conductor of diameter d, length 1 consumes a power of W when a current I flows through it. What will be the power consumed if d is doubled, 1 is halved and current is tripled ?

asked Apr 23, 2018 in Electrical Engineering by Zeeshan
1 answer 12 views

What is the diameter of the GI pipe through which the earth wire needs to be taken out?

asked May 29, 2018 in Electrical Engineering by Shimroz123
0 answers 10 views

Moving coil instruments have which one of the following scales ? (a) Logarithmic scale (b) Uniform scale (c) Non-uniform scale (d) Squared scale 

asked May 26, 2018 in Physics by Shimroz123
1 answer 4 views

Which of the following notations have two repetitions of zero ?  (P) 1’s complement with radix of number being 2  (Q) 7’s complement with radix of number being 8.  (R) 9’s complement with radix of number being 10.  (S) 10’s complement with radix of number being 10   Select the correct answer using the codes given below:   (a) P,Q and S (b) P and R (c) Q, R and S (d) P,Q and R

asked May 13, 2018 in Electronics Engineering by Shimroz123
1 answer 20 views

An absolutely integrable signal x(t) is known to have a pole at s = 2. Which one of the following is true ? (A) B, C and D are true (B) x(t) can be left-sided (C) x(t) can be right-sided (D) x(t) can be both-sided

asked May 12, 2018 in Control System by Shimroz123
1 answer 21 views

Which of the following does not have a commutator? A) Dynamo B) Induction motor C) Universal motor D) None of these

asked Apr 29, 2018 in Electrical Machine by Shimroz123
1 answer 12 views

Which of the following flip-flop do not have race problem ? a)T flip-flop b) D flip-flop c) JK flip-flop d) Master Slave flip-flop

asked Apr 14, 2018 in Instrumentation and control by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...