46 views
in Electrical Engineering by
In order to recover the original signal from the Sampled one, what is the condition to be satisfied for sampling frequency ωs and highest frequency component ωm? 

(A) ωm < ωs ≤ 2 ωm (B) ωs ≥ 2 ωm (C) ωs < ωm (D) ωs = ωm

Related questions

0 answers 19 views

A signal m(t) = 3cos(6000nt)+4cos(7000nt)+5cos(100001-it) to be sampled. What is the minimum sampling rate for band pass sampling for truth full representation : a. 2000 Hz b. 3000 Hz c. 5000 Hz d. 10000 Hz

asked Apr 12, 2018 in Electronics Engineering by Shimroz123
0 answers 45 views

The sampling rate to avoid aliasing for the signal m(t) = 100 cos 200ωt will be A) ≥1/25 sec B) ≥1/50 sec C) ≤1/25 sec D) ≤ 1/50 sec

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
0 answers 43 views

The signal is extended from 96KHz to 100KHz, so the minimum sampling frequency required is  (a) 8KHz (b) 200KHz (c) 4KHz (d) 100KHz

asked Apr 9, 2018 in Electronics communication by Shimroz123
1 answer 40 views

 If a signal band limited to fm is sampled at a rate less than 2fm, then the constructed signal will be A) Large in amplitude B) Small in amplitude C) Distorted D) Distortion less

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
0 answers 26 views

For a waveform to be expressed in Fourier series, which of the following conditions must be satisfied? I. Maxwell’s conditions, II. Drichlet conditions, III. Sampling Theorem A) I only B) II only C) II and III only D) I, II and III

asked Jun 17, 2018 in Electrical Engineering by Shimroz123
0 answers 17 views

One of the necessary and sufficient condition for a network function N(s)=p(s)/q(s) to be a transfer function is that  A) The coefficients of the polynomial p(s) and q(s) must be real and those for q(s) must be positive B) Coefficients of p(s) and q(s) must be real and positive C) Coefficients of p(s) must be positive and real but coefficients of q(s) can be negative also D) Degree of p(s) and q(s) may differ by either zero or one only

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 23 views

The analog signal given below is sampled by 600 samples per second for m(t) = 3 sin 500 pt + 2 sin 700 pt then folding frequency is: (1) 500 Hz (2) 700 Hz (3) 300 Hz (4) 1400 Hz 

asked May 28, 2018 in Analog electronics circuits by Shimroz123
0 answers 24 views

A separately excited dc motor is required to be controlled, from a 3-phase supply, for its operation in the first quadrant only. The most preferred converter would be  (a) 3-phase fully controlled converter (b) 3-phase fully controlled converter with free wheel diode (c) 3-phase dual converter (d) 3-phase half wave converter 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 25 views

What is the flow of electrons from one atom to another called?

asked Mar 14, 2018 in Electrical Engineering by Quiz
0 answers 39 views

For a transient stability analysis, as long as equal area criterion is satisfied, the maximum angle to which rotor angle can oscillate is:  (A) 0˚ to 20˚ (B) 45˚ to 50˚ (C) Greater than 90˚ (D) 65˚ to 85˚

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 63 views

For an analog PLL, under perfect locking condition, the phase difference (in degrees) between input signal and VCO output should be  A) 0 B) 90 C) 120 D) 180

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 82 views

A drawn wire of resistance 5 Ω is further drawn so that its diameter becomes one-fifth of the original. What is its resistance with volume remaining the same ? (a) 25 Ω (b) 125 Ω (c) 625 Ω (d) 3125 Ω

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 62 views

In order to switch-off and EHV circuit for maintenance, the following sequence is adopted: (1) Open the circuit breaker, open the isolator, operate the earth switch (2) Operate the earth switch, open the isolator, open the circuit breaker (3) Open the isolator, operate the earth switch, open the circuit breaker (4) Open the isolator, open the circuit breaker, operate the earth switch 

asked May 29, 2018 in Electrical Engineering by Shimroz123
1 answer 32 views

Which of the following TCP/IP protocol is used for transferring electronic mail messages from one machine to another?  (a) FTP (b) SNMP (c) SMTP (d) RPC

asked May 23, 2018 in Computer Engineering by Shimroz123
0 answers 18 views

A coherent QPSK demodulator is required on ground for receiving data from a LEO satellite. What should be optimum order of PLL in the carrier phase tracking loop?  A) 1st order B) 2nd order C) 3rd order D) None of the above

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
0 answers 12 views

What is the maximum number of points of light, fan and socket-outlets that can be connected in one sub-circuit ?   (a) 5 (b) 10 (c) 20 (d) 30 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 21 views

Which one is not a valid condition for the wave winding? A) Back pitch and front pitch are of the same sign B) Back pitch and front pitch are odd numbers C) Back pitch and front pitch may differ by two and may be equal also D) Commutator pitch is always unity

asked Jun 17, 2018 in Electrical Machine by Shimroz123
1 answer 20 views

The necessary and sufficient condition for a rational function of, T(s) to be driving point impedance of an RC network is that all poles and zeros should be

asked Apr 29, 2018 in Network Analysis by Shimroz123
1 answer 33 views

The analog signal m(t) is given below m(t) = 4 cos 100 pt + 8 sin 200 pt + cos 300 pt, the Nyquist sampling rate will be: (1) 1/100 (2) 1/200 (3) 1/300 (4) 1/600 

asked May 28, 2018 in Analog electronics circuits by Shimroz123
1 answer 2 views

List the different techniques used for signal conditioning in DAS. Explain in brief Any one signal conditioning technique.

asked Sep 13, 2018 by Shimroz123
0 answers 16 views

500 Bytes of data needs to be transmitted from an UART every lOOms. What should be the minimum transmission baud rate of UART, assuming 1 start bit, 8 data bits and 2 stop bits?  A) 50000 B) 55000 C) 40000 D) 45000

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
0 answers 22 views

Under no load condition, if the applied voltage to an induction motor is reduced from the rated voltage to half the rated value,  (A) the speed decreases and the stator current increases (B) both the speed and the stator current decreases (C) the speed and the stator current remain practically constant (D) there is negligible change in the speed but the stator current decreases

asked May 17, 2018 in Induction Machine by Shimroz123
1 answer 51 views

In order to get maximum power transfer from a capacitive source, the load must? A.have a capacitive reactance equal to circuit resistance B.have an impedance that is the complex conjugate of the source impedance C.be as capacitive as it is inductive D.none of the above

asked May 15, 2018 in Basic concepts by Shimroz123
0 answers 15 views

In a fiber-optic cable, which phenomenon occurs for signal to propagate along the inner core:  A) Modulation B) Reflection C) Refraction D) All of the above

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

The current in a 200 mH coil increases from 2 to 5 A in 0.1 Second. What is rate of change of current? A. 30 A/s B. 20 A/s C. 10 A/s D. none of these

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
0 answers 29 views

What is the equivalent resistance of one limb A when delta connection is transformed in to star?  (A) R1R3/R1+R2+R3 (B) R2R3/R1+R2+R3 (C) R1R2R3/R1+R2+R3 (D) R1+R2+R3

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

The amount of current in a resistor needs to be changed from 120 mA to 160 mA by changing the 24 V source, the new voltage will be: A. 8 V B. 320 V C. 3.2 V D. 32 V

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

An absolutely integrable signal x(t) is known to have a pole at s = 2. Which one of the following is true ? (A) B, C and D are true (B) x(t) can be left-sided (C) x(t) can be right-sided (D) x(t) can be both-sided

asked May 12, 2018 in Control System by Shimroz123
1 answer 308 views

In order to regulate steady state error to zero, in a negative feedback control system, one employs

asked May 1, 2018 in Control System by Shimroz123
0 answers 21 views

A point charge of 120 mC is placed at the centre of a cube. What will be the total flux passing through one face of the cube?  A) 120 mC B) 60 mC C) 20 mC D) 30 mC

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 593 views

In a step-up or step-down transformer, electrical power is transferred from one circuit to another without change in

asked May 14, 2018 in Transformer by Shimroz123
0 answers 17 views

One of the following Memories has the highest speed in terms of data transfer to and from the processor.  (1) Cache Memory (2) Primary Memory (3) Secondary Memory (4) External memory

asked Apr 10, 2018 in Computer Engineering by Shimroz123
0 answers 20 views

A transmission line to be reciprocal, the condition is (a) A = D (b) AC – BD = 1 (c) AD – BC = 1 (d) AB – CD = 1  

asked May 25, 2018 in Electric Power Transmission by Shimroz123
1 answer 17 views

What is the correct sequence of the following materials in ascending order of their resistivity ?  1. Iron  2. Silver  3. Constantan  4. Mica  5. Aluminium  Select the correct answer using the codes given below :  (a) 2, 5, 1, 3 and 4  (b) 4, 5, 3, 1 and 2  (c) 2, 3, 1, 5 and 4  (d) 4, 5, 1, 3 and 2

asked Apr 23, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

The change in value of an analog signal during the conversion process produces what is called the : -  a) quantization error b) resolution error c) Nyquist error d) sampling error

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 21 views

In order to reduce cross sectional dimension, the wave guide to use is 

asked May 23, 2018 in Electrical Engineering by Shimroz123
1 answer 73 views

Which of the following are satisfied in a non-linear network ?  1. Associative  2. Superposition  3. Homogeneity  4. Bilaterality  Select the correct answer using the codes given below :  (a) 1 and 3 only (b) 1 and 4 only (c) 2 and 3 only (d) 2 and 4 only

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

In order to generate electron-hole pairs, the maximum wavelength of radiation for Silicon (Band gap = 1.1 eV) is  (a) 1.88 μm (b) 1.68 μm (c) 1.13 μm (d) 1.54 μm

asked May 15, 2018 in Physics by Shimroz123
0 answers 26 views

A menu driven operating system is one which allows you to pick up from the menu of choices it displays on the screen. What is the name given to the images which are used in such image oriented menus?  (1) Model (2) Figure (3) Symbol (4) Icon 

asked Apr 10, 2018 in Computer Engineering by Shimroz123
0 answers 14 views

By which of the following connections, one-bit binary counter can be obtained from a JK flip-flop?  A) J = K = 0 B) J = K = 1 C) J = K’ D) None of these

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
2 answers 74 views

The sum of product expression for a Boolean function can be derived from its truth table by (a) AND operation of the product terms. (b) NOR operation of the product terms. (c) OR operation of the product terms. (d) NAND operation of the product terms.

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 19 views

What is the movement of electrons from atom to atom is called?

asked Mar 14, 2018 in Electrical Engineering by Quiz

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...