20 views
in Electronics Engineering by
In satellite communication, Ku band (in GHz) refers to 

A) 4-8 B) 8-12 C) 12-18 D) 18-27

Related questions

1 answer 10 views

The Ku frequency band used in satellite communication (for uplink and downlink) is: (1) 14 GHz and 11 GHz (2) 30 GHz and 20 GHz (3) 70 GHz and 50 GHz (4) 60 GHz and 45 GHz 

asked May 29, 2018 in Electronics communication by Shimroz123
0 answers 18 views

In satellite communication, frequency modulation is used because satellite channel has  a. High modulation index  b. Small bandwidth and negligible noise  c. Large bandwidth and severe noise   d. Maximum bandwidth and minimum noise

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 21 views

An Ideal power limited communication channel with additive white Gaussian noise with 1 MHz band width and Signal to Noise ratio of 15 is transmitting the information at theoretical maximum rate. If the Signal to Noise ratio is reduced to 7, how much bandwidth is required to maintain same rate: a. 15/7 MHz b.4/3 MHz c. 2 MHz d. None of these

asked Apr 12, 2018 in Electronics Engineering by Shimroz123
0 answers 14 views

 An Ideal power limited communication channel with additive white Gaussian noise is having 4 KHz band width and Signal to Noise ratio of 255. The channel capacity is: a. 8 kilo bits /sec b. 9.63 kilo bits / Sec c. 16 kilo bits / Sec d. 32 kilo bits / Sec

asked Apr 12, 2018 in Electronics Engineering by Shimroz123
0 answers 33 views

In satellite communication, scrambling is mainly used for -  A) I clock recovery B) encryption C) limiting power spectral density D) bandwidth efficiency

asked Apr 9, 2018 in Electronics communication by Shimroz123
0 answers 10 views

"Cycle Stealing" in microprocessor parlance refers to a. Special type of DMA access by an external device b. RESET operation at power ON by microprocessor c. Interrupt Acknowledge cycle d. none of above..

asked Apr 12, 2018 in Electronics Engineering by Shimroz123
0 answers 20 views

Propagation medium of the signal in band (3 to 30) MHz is by  A) Space wave B) Surface wave C) Sky wave D) LOS

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 6 views

 Communication between satellite and ground station is through : (A) Tropospheric scatter (B) Ground wave (C) Sky wave (D) Line of sight propagation

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 12 views

In communication systems, noise due to quantization error is a) Linear and signal dependent b) Non-linear and signal dependent c) Linear and signal independent at low frequencies only d) non -linear and signal dependent at low frequencies only

asked Jun 15, 2018 in Electronics Engineering by Shimroz123
1 answer 15 views

Companders are used in communication systems to:  (1) Compress bandwidth (2) To improve frequency response (3) To improve signal to noise ratio (4) None of these

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 14 views

The term “white noise” refers to the following: (1) A random signal with flat power spectral density (2) A random signal generated by beat signal (3) A random signal with long range correlation (4) All of the above are true 

asked May 29, 2018 in Electronics Engineering by Shimroz123
0 answers 44 views

Darlington pair amplifier refers to cascaded combination of  A) Two common collectors B) Common collector and common emitter C) Common Base and Common emitter D) None of the above

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 40 views

 If a signal band limited to fm is sampled at a rate less than 2fm, then the constructed signal will be A) Large in amplitude B) Small in amplitude C) Distorted D) Distortion less

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
0 answers 12 views

 For identical total transmitted power, the ratio of S/N for wide band FM to S/N of DSB-AM (with ma=1) is : ( Given fm = 15 KHz & frequency. deviation =+/- 75 KHz) a. 112.5 b. 300 c. 75 d. 450

asked Apr 12, 2018 in Electronics Engineering by Shimroz123
1 answer 31 views

Which one of the following statements is correct? Digital modulation techniques are used in satellite communication systems since:  (1) They are easier to handle (2) Large bandwidth utilization is possible (3) They have a higher spectral efficiency (4) They are less prone to interference

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 15 views

Orbital velocity (in km/S) of Geosynchronous satellite is about  A) 1.83 B) 2.62 C) 2.91 D) 3.07

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 8 views

Orbital altitude of MEO satellite is in the range of  A) (10000 -20000) km B) (750-1500)km C) (200-600)km D) None of these

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 20 views

The band gap of elements arranged in ascending order is : a. Diamond, Ge, Si b. Si, Ge, Diamond c. Ge, Si, Diamond d. Diamond, Si, Ge

asked Apr 12, 2018 in Electronics Engineering by Shimroz123
0 answers 29 views

The FM radio broad cast frequency band (in MHz) is  A) 68-98 B) 88 -108 C) 148 – 268 D) None of these 

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 22 views

Television channel allocation (in MHz) for VHF band III is  A) 47-68 B) 174-230 C) 470-582 D) 606-870

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 16 views

The line of sight communication requires transmit and receive antenna to face each other. If the transmit antenna is vertically polarized, for the best reception the receive antenna should be:  (1) Horizontally polarized (2) Vertically polarized (3) At 45° with respect to the horizontal polarization (4) At 45° with respect to the vertical polarization

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 14 views

In value engineering, the term value refers to : (A) manufacturing cost of the product (B) selling price of the product (C) total cost of the product (D) utility of the product

asked Jun 14, 2018 in Mechanical Engineering by Shimroz123
1 answer 10 views

The body effect in the MOS technology refers to  (A) size of the drain on the drain current  (B) doping of the drain on the drain current  (C) effect of the reverse bias voltage between source and body on the drain current  (D) effect of the reverse bias voltage between drain and body on the drain current

asked May 12, 2018 in MOSFET by Shimroz123
1 answer 17 views

In steam turbine terminology, diaphragm refers to  (1) separating wall between rotors carrying nozzles (2) the ring of guide blades between rotors (3) a partition between low and high pressure sides (4) the flange connecting the turbine exit to the condenser

asked Apr 29, 2018 in Electric Power Generation by Shimroz123
0 answers 12 views

The term operator overloading in C++ refers to:  (1) Inheritance (2) Message passing (3) Polymorphism (4) None

asked Apr 10, 2018 in Computer Engineering by Shimroz123
1 answer 31 views

A 4 GHz carrier is amplitude modulated by a low-pass signal of maximum cut off frequency 1 MHz. lf this signal is to be ideally sampled, the minimum sampling frequency should be nearly

asked Apr 26, 2018 in Electronics Engineering by Shimroz123
0 answers 19 views

The gain of a parabolic dish antenna of 1 m diameter -and 80% efficiency at 9.5 GHz is: a. 39 dB b. 78 dB c. 40 dB d. 45 dB

asked Apr 12, 2018 in Electronics Engineering by Shimroz123
1 answer 24 views

In a broadcast communication receiver, most of the receiver selectivity is achieved in: (1) RF section (2) IF section (3) Mixer (4) Local oscillator 

asked May 29, 2018 in Electronics Engineering by Shimroz123
1 answer 18 views

In order to generate electron-hole pairs, the maximum wavelength of radiation for Silicon (Band gap = 1.1 eV) is  (a) 1.88 μm (b) 1.68 μm (c) 1.13 μm (d) 1.54 μm

asked May 15, 2018 in Physics by Shimroz123
0 answers 18 views

When the communication line run parallel to the power lines in close proximity  P. The electromagnetic effect produces current due to induction resulting its superposition on the speech signal of the communication line causing distortion  Q. The electrostatic effect raises the potential of the communication circuit as a whole and thereby posing a threat of damage to the ... lines  Which of the following combinations is valid?  A) R only B) P, Q & R C) P & Q only D) P & R only

asked Apr 9, 2018 in High voltage engineering by Shimroz123
1 answer 6 views

When a dominant mode wave guide not terminated in its characteristic impedance is excited with a 10 GHZ signal then if d is the distance between two successive minima of the standing wave in the guide then   (A) d = 1.5 cm (B) d is less then 1.5 cm (C) d is greater then 1.5 cm (D) d = 3 cm

asked May 17, 2018 in Electronics communication by Shimroz123
1 answer 6 views

A band pass filter is that which

asked May 15, 2018 in Electronics Engineering by Shimroz123
0 answers 19 views

Semiconductor A has a higher band gap than semiconductor B. If both A and B have the same dimensions, the same number of electrons at a given temperature and the same electron and hole mobilities, then

asked Mar 31, 2018 in Electronics Engineering by Shimroz123
1 answer 7 views
1 answer 16 views

Production cost refers to prime cost plus : (A) factory overheads (B) factory and administration overheads (C) factory, administration and sales overheads (D) factory, administration, sales overheads and profit

asked Jun 14, 2018 in Mechanical Engineering by Quiz
1 answer 9 views

Making current of a circuit breaker refers to: (1) Steady state rated current (2) Average value of transient short circuit current (3) R.M.S. value of the short circuit current at the the time of major peak (4) Equal to the fault current

asked May 22, 2018 in Circuit breaker by Shimroz123
1 answer 27 views

Dry etching refers to removal of material, typically a masked pattern of semiconductor material, by exposing material to a bombardment of ions which contain (a) Plasma of nitrogen, chlorine and boron trichloride (b) Plasma of sodium, chlorine and boron trichloride (c) Plasma of nitrogen, phosphorous and boron trichloride (d) Plasma of nitrogen, chlorine and boron trioxide

asked Apr 14, 2018 in Electrical Engineering by Zeeshan
1 answer 20 views

Base 10 refers to which number system? a) binary coded decimal b) decimal c) octal d) hexadecimal

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
0 answers 18 views

Choose the correct statements,  (1) Casting refers to implicit type conversion (2) Coercion refers to explicit type conversion (3) Casting refers to explicit type conversion (4) None of these

asked Apr 10, 2018 in Computer Engineering by Shimroz123
0 answers 46 views

The bandwidth and S/N of a communication system are 3MHz and 30dB respectively. The channel capacity (in Mbps) is around  A) 30 B) 300 C) 0.3 D) None of these

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 12 views

Earth coverage dish antenna is used in satellite system. It is characterized by the fact that  (a) It is a narrow beam antenna (b) It is Parabolic antenna (c) it is sharply focused within a small area of the surface of the earth (d) it is a wide angle antenna which covers a large area of the surface of the earth

asked May 15, 2018 in Electronics communication by Shimroz123
1 answer 74 views

The colour band on the extreme left in general purpose fixed resistors represents: A) Tolerance B) First significant digit C) Wattage Rating D) Voltage Rating

asked Jun 18, 2018 in Electrical Engineering by Shimroz123
0 answers 45 views

An electron in the conduction band has (A) More energy than the electron in the valence band (B) Lesser energy than the electron in the valence band (C) Same energy as that of the electron in the valence band (D) No energy at all 

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 7 views

Regenerative repeaters are placed along the communication path to control:  a. Power b. Noise c. Frequency d. Amplitude 

asked May 17, 2018 in Telecommunication Engineering by anonymous

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,450 questions

7,047 answers

132 comments

3,084 users

...