16 views
in Electronics Engineering by
Output of an op-amp is a square wave of 4 V peak to peak with a rise time of 5 microsecond and fall time of 4 microsecond.Maximum frequency (in kHz)of undistorted sine wave output of 2 V peak to peak is about 

A) 100 B) 150 C) 200 D) 250

Related questions

1 answer 9 views

An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

asked Jul 10 in Elements of Electronics by Shimroz123
1 answer 31 views

In a 741 Op-Amp, there is 20 dB/decade fall-off starting at a relatively low frequency. This is due to the (A) applied load (B) internal compensation (C) impedance of the source (D) power dissipation in the chip

asked Apr 26, 2018 in Electronics Engineering by Shimroz123
0 answers 21 views

A ramp voltage V(t)=100 V is applied to an RC differentiating circuit with R=5 kΩ and C=4 μF. The maximum output voltage is  (A) 0.2 V (B) 2 V (C) 10 V (D) 50 V

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 8 views

For an SCR with turn-on time of 5 microsecond, an ideal trigger pulse should have   (a) short rise time with pulse width = 3 µsec (b) long rise time with pulse width = 6 µsec (c) short rise time with pulse width = 6 µsec (d) None of the above 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
0 answers 11 views

A peak reading voltmeter has been calibrated with a sine wave signal and scaled in rms volts. If a square wave signal ± 1V peak is applied, the meter reading will be (a) 0.555 V (b) 0.707 V (c) 1 V (d) 1.75 V

asked May 25, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 112 views

The time/div and voltage/div axes of an oscilloscope have been erased. When a 1 kHz, 5V p-p square wave calibration pulse is connected to channel 1 ofthe scope the waveform observed on the screen is as shown in the upper trace of the figure. An unknown signal is connected to channel 2 (lower trace) ofthe scope. If the time/div and V/div on both channels are the same, the amplitude (pp) and period of the unknown signal are respectively.

asked May 20, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 70 views

An op-amp having a slew rate of 62.8 V/msec, is connected in a voltage follower configuration. If the maximum amplitude of the sinusoidal input is 10 V, then the minimum frequency at which the slew rate limited distortion would set in at the output is  (A) 1 MHz (B) 6.28 MHz (C) 10 MHz (D) 62.8 MHz

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 30 views

A 4-bit R/2R digital-to-analog (DAC) converter has a reference of 5 volts. What is the analog output for the input code 1010:  (1) 0.3125 V (2) 3.125 V (3) 0.78125 V (4) –3.125 V

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 34 views

An OP amp has a slew rate of 1V/µs. At a signal frequency of 0.1 MHz, the maximum undistorted sine wave amplitude is (a) 8V (b) 4.82 V (c) 2.02 V (d) 1.592 V

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 6 views

Rise time of an amplifier is found to be 1.0µS, its bandwidth (in kHz) is around  A) 2200 B) 1000 C) 350 D) 220 

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 13 views

The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc voltage with resistive load and without filter will be • 12.1 volt • 1.21 volt • 0.482 volt • 4.82 volt

asked May 13, 2018 in Electronics Engineering by Shimroz123
1 answer 33 views

An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak Envelope Power? A) 49.98 W B) 79.98 W C) 99.96 W D) 199.93 W

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
0 answers 14 views

An average reading digital multimeter reads 10 V when fed with a triangular wave, symmetric about the time axis. For the same input the r.m.s. reading meter will read

asked May 25, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 21 views

A dc shunt motor runs at 500 r.p.m at 220 V. A resistance of 4.5 Ω is added in series with the armature for speed control. The armature resistance is 0.5 ohms. The current to stall the motor will be (1) 44 A (2) 50 A (3) 44.4 A (4) 60 A  

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 37 views

 An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to secondary turn’s ratio 12:1. The peak inverse voltage is A) 8.62 V B) 12 V C) 19.17 V D) 27.11 V 

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
0 answers 52 views

A dominant pole compensated op-amp has openloop gain of 100 dB and -3 dB bandwidth of 50 Hz. If it is connected as inverting amplifier for a gain of 20 dB the -3 dB bandwidth is about  A) 500 kHz B) 50 kHz C) 5 kHz D) 500 Hz

asked Apr 5, 2018 in Electronics Engineering by Shimroz123
1 answer 15 views

The input voltage to an OP AMP is a large voltage step. The output is an exponential waveform that changes to 0.25 V in 0.1µs (microsecond). The slew rate of the OP AMP is : -  a) 5V/µs b) 2.5 V/ µs c) 3V/µs d) 4.5V/ µs

asked Apr 10, 2018 in Instrumentation and control by Shimroz123
1 answer 8 views

What is the time of operation of a relay of rating 5 amp 2.2 sec, IDMT and having a relay of setting of 125% Tms = 0.6 It is connected to a supply circuit through a CT, 400 ratio. The fault current is 400 amp.

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 26 views

What is the line current of a circuit when the current transformer of 1000 : 5 rating measures 4 amp? (A) 5000 amp (B) 1000 amp (C) 400 amp (D) 800 amp 

asked Apr 23, 2018 in Instrumentation and control by Shimroz123
0 answers 33 views

What is the Output voltage of Op-amp for input voltage of Vi1=150 μV,Vi2=140 μV if the amplifier has differential gain of Ad=4000 and value of CMRR is 100. 

asked Apr 4, 2018 in Electrical Engineering by Shimroz123
1 answer 48 views

The output voltage waveform of a three-phase square-wave inverter contains  (A) only even harmonics (B) both odd and even harmonic (C) only odd harmonics (D) only triple harmonics

asked May 18, 2018 in Power electronics converters by Shimroz123
1 answer 54 views

If a transformer primary is energised from a square wave voltage source, its output voltage will be a:  (A) square wave (B) sine wave (C) triangular wave (D) pulse wave

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 72 views

D.C. motor is to drive a load which has certain minimum value for most of the time and some peak value for short duration. We will select the?

asked Mar 20, 2018 in DC motor by Shimroz123
1 answer 77 views

In a full wave rectifier with input frequency of 50 Hz, the frequency of the output is: (1) 50 Hz (2) 100 Hz (3) 150 Hz (4) 200 Hz

asked May 29, 2018 in Electronics Engineering by Shimroz123
1 answer 14 views

The average value of a 12 V peak sine wave over one complete cycle is? A.0 V B.1.27 V C.7.64 V D.6.37 V

asked May 15, 2018 in Basic concepts by Shimroz123
1 answer 9 views

If the peak value of a sine wave is 30 V, the rms value is? A.19.08 V B.7.07 V C.0.707 V D.23.10 V

asked May 15, 2018 in Basic concepts by Shimroz123
1 answer 10 views

The threshold effect in demodulators is a) The rapid fall of output SNR when the input SNR falls below a particular value b) Exhibited by all the demodulators when the input SNR is low c) Exhibited by all AM suppressed carrier coherent demodulators d) Exhibited by correlation receivers

asked Jun 15, 2018 in Electronics Engineering by Shimroz123
1 answer 10 views

The current through a flashlight bulb is 40 mA and the total battery voltage is 4.5 V. The resistance of the bulb is approximately? A.112 ohms B.11.2 ohms C.1.2 ohms D.18 ohms

asked May 15, 2018 in Basic concepts by Shimroz123
0 answers 19 views

If frequency is decreased 4 times, then skin depth of an Electromagnetic wave inside a conductor will be :  A) halved B) quadrupled C) doubled D) no change

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 12 views

A single phase transformer is designed to operate from 50 Hz, 1100 V supply and to have an output voltage of 240 V at no load. The core has mean area of 30 cm2 and the flux density has not to exceed 1.3T. The number of secondary turns will be (a) 1270 (b) 1017 (c) 768 (d) 277  

asked May 25, 2018 in Single phase transformer by Shimroz123
1 answer 7 views

A single-phase, 230 V, 50 Hz ac mains fed step down transformer (4:1) is supplying power to a half-wave uncontrolled ac-dc converter used for charging a battery (12 V dc) with the series current limiting resistor being 19.04 Ohm. The charging current is  (A) 2.43 A (B) 1.65 A (C) 1.22 A (D) 1.0 A

asked May 18, 2018 in Power electronics converters by Shimroz123
0 answers 20 views

The duty ratio of a step-up chopper with an output voltage of 200 V from a 80 V dc source, is (A) 0.4 (B) 0.5 (C ) 0.6 (D) 1.5 

asked Jun 4, 2018 in Power Electronics by Shimroz123
0 answers 9 views

An ideal Op Amp has  (a) infinite input and output impedance (b) very low input and output impedance (c) low input impedance and very high output impedance (d) infinite input impedance and zero output impedance

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 14 views

An op-amp can be represented by  A) Norator at input and Nullator at output B) Norator at output and Nullator at input C) Norator at input and output D) Nullator at input and output

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 12 views
0 answers 29 views

For an ADC, full scale output voltage is about 10 V.For a resolution of about 9.78mV, number of bits required is  A) 6 B) 8 C) 10 D) 12

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 36 views

An antenna located in a city is a source of radio waves. How much time does it take the wave to reach a town 12,000 km away from the city?  a. 36 s b. 20 us c. 20 ms d. 40 ms 

asked May 17, 2018 in Telecommunication Engineering by anonymous
0 answers 21 views

For an 8 bit DAC, reference voltage is 10 V. If input to DAC starting from MSB is 10111100, output (in volts) is  A) 5.8 B) 6.4 C) 7.3 D) 8.2

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 14 views

Velocity of an electron (in km/S) starting at rest and travelling to a point 100 V above the starting potential is around  A) 3600 B) 4000 C) 5100 D) 6000

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 14 views

A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is (A) 300 W (B) 150 W (C) 45 W (D) 20 W

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 11 views

An Op-amp as a voltage follower has a voltage gain of

asked May 14, 2018 in Amplifier by Shimroz123
0 answers 17 views

A 12-bit ADC is operating with a lus clock period and total conversion time is seen to be 14us always. The ADC must be of the type  a. Flash type b. Counting type c. Integrating type d. Successive approximation type

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 22 views

 In an electronic ohmmeter an op -amp is used as a: -  a) sommer b) multiplier c) buffer amplifier d) integrator

asked Apr 10, 2018 in Instrumentation and control by Shimroz123
0 answers 23 views

The output voltage of a battery drops from 100 V with zero load current to 80 V when load current is 2 A. The internal resistance of the battery is (a) 10 Ω (b) 20 Ω (c) 40 Ω (d) 50 Ω

asked May 25, 2018 in Battery by Shimroz123
1 answer 15 views

In a half-wave rectifier, if an a.c supply is 60 Hz. Then what is the a.c ripple at output? (A) 30 Hz (B) 60 Hz (C) 20 Hz (D) 15 Hz

asked Apr 26, 2018 in Electronics Engineering by Shimroz123
1 answer 17 views

 If the range of an analog transducer is 0 to 10 V, then for a resolution of 5 mV, the bits of ADC will be _____.

asked May 29, 2018 in Transducers and sensors by Shimroz123
0 answers 27 views

A Reactor having an inductive reactance of 4 ohm is connected to the terminals of a 120 V AC generator. Calculate the power associated with the reactor.  (A) 3.6 kvar (B) 30 kvar (C) 7.2 kvar (D) 4.16 kvar 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 8 views

The input impedance of an op-amp is • High • Low • Medium • None of the above

asked May 14, 2018 in Amplifier by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,450 questions

7,047 answers

132 comments

3,085 users

...