Can you help by answering this question?

What is considered telecommunication equipment?

1,389 views
in Electronics Engineering by
In an amplitude modulated system if the total power is 600W and the power in the carrier is 400W, the modulation index is 

a. -0.5 b. 0.75 c. 0.9 d. l

Your answer

Thanks for your contribution. Feel free to answer this question. Please avoid short answer. Your answer is most welcome. Be genuine.

Upload image or document:

Your name to display (optional):
Privacy: Your email address will only be used for sending these notifications.
Anti-spam verification:
Are you a robot ? (Y = Yes / N = No)
To avoid this verification in future, please log in or register.

Related questions

1 answer 31 views

A 4 GHz carrier is amplitude modulated by a low-pass signal of maximum cut off frequency 1 MHz. lf this signal is to be ideally sampled, the minimum sampling frequency should be nearly

asked Apr 26, 2018 in Electronics Engineering by Shimroz123
1 answer 27 views

The total power of an AM transmitter having a carrier power of 50 W and the percentage of modulation at 80% is A) 50 W B) 66 W C) 68 W D) 70 W 

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
0 answers 33 views

A carrier signal of 600 V rms with 75% amplitude modulation is applied to 75 ohm antenna. The total side band power (in watts) is  A) 4800 B) 450 C) 950 D) 1350 

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 22 views

In an amplitude modulated wave. the value of V is max 10V and Vmin is 5V, then % modulation is : (A) 25% (B) 33.3% (C) 50% (D) 100%

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 29 views

In a microwave test bench, why is the microwave signal amplitude modulated at 1 kHz?  (1) To increase the sensitivity of measurement (2) To transmit the signal to a far-off place (3) To study amplitude modulation (4) Because crystal detector fails at microwave frequencies

asked May 29, 2018 in Electronics Engineering by Shimroz123
1 answer 19 views

If the carrier of a 100 percent modulation modulated AM wave is suppressed, the percentage power saving will be (A) 50.55 (B) 15.55 (C) 10.66 (D) 66.66

asked May 12, 2018 in Computer Engineering by Shimroz123
1 answer 25 views

If the radiated power of AM transmitter is 10 KW, the power in the carrier for modulation index of 0.6 is nearly:  (1) 8.24 KW (2) 9.26 KW (3) 8.47 KW (4) 9.6 KW

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 32 views

 AM transmitter has a carrier power of 30 W. The percentage of modulation is 85%. Calculate the total power : (A) 5.4 W (B) 40.8 W (C) 10.8 W (D) 20.4 W

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 250 views

If the reference bus is changed in two load flow runs with same system data and power obtained for reference bus taken as specified P and Q in the latter run, the system losses  A) Will be unchanged but complex bus voltages will change B) Will change but complex bus voltage remain unchanged C) As well as complex bus voltage will changed D) As well as complex bus voltage will be unchanged

asked May 20, 2018 in Power system by Shimroz123
0 answers 23 views

A Power system has a total load of 1260 MW at 50 Hz. The load varies 1.5% for every 1% change in frequency. Find the steady state frequency deviation, when a 60 MW load is suddenly dripped if there is no speed control.  (A) 1.667 Hz (B) 50 Hz (C) No change (D) 3.32 Hz 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 22 views

The maximum transmission power efficiency of DSB-C Amplitude modulation is : a. 25% b. 33.33% c. 50% d. 100%

asked Apr 12, 2018 in Electronics Engineering by Shimroz123
0 answers 114 views

If X is the system reactance and R is its resistance, the power transferred is maximum when (1) X=R (2) X=1.414 R (3) X=1.732 R (4) X=2R 

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

The amplifiers following the modulated stage in a low level modulation AM system be  (A) linear amplifier (B) harmonic generators (C) class C power amplifiers (D) class untuned amplifiers

asked May 17, 2018 in Amplifier by Shimroz123
0 answers 70 views

. If the peak transmitted power in a radar system is increased by a factor of 16, the maximum range will be increased by a factor of : (A) 2 (B) 4 (C) 8 (D) 16

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

The frequency of carrier in the carrier current pilot scheme is : (A) 1 kHz to 10 kHz (B) 25 kHz to 50 kHz (C) 10 kHz to 25 kHz (D) 50 kHz to 500 kHz

asked May 12, 2018 in Electronics Engineering by Shimroz123
0 answers 42 views

The following statements are made for NMOS & PMOS 1. The carrier mobility in NMOS is higher 2. PMOS require less area than NMOS 3. NMOS circuits are smaller than PMOS 4. PMOS are faster in switching. Of these, the true statements are : a. 2 and 4 only b. 2 and 3 only c. 1 and 3 only d. 1, 2 and 3 only

asked Apr 12, 2018 in Electronics Engineering by Shimroz123
0 answers 12 views

 For identical total transmitted power, the ratio of S/N for wide band FM to S/N of DSB-AM (with ma=1) is : ( Given fm = 15 KHz & frequency. deviation =+/- 75 KHz) a. 112.5 b. 300 c. 75 d. 450

asked Apr 12, 2018 in Electronics Engineering by Shimroz123
0 answers 21 views

If the antenna diameter in a radar system is increased by a factor of 4, the maximum range will be increased by a factor of  (a) 2 (b) 4 (c) 8 (d) 16

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 38 views

The response of an LTI/LSI system is given by the _______ of input and impulse response:  (1) Convolution (2) Correlation (3) Superposition (4) None

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 20 views

In the case of a 70–MHz IF carrier for a transponder bandwidth of 36 MHz, energy must lie between MHz: (1) 34 and 106 (2) 52 and 88 (3) 106 and 142 (4) 34 and 142

asked May 28, 2018 in Electronics communication by Shimroz123
0 answers 37 views

In an n-bus power system, considering n-nodes network, the size of ybus is   (a) (n – 1) × (n – 1) (b) (n + 1) × (n + 1) (c) n × n (d) 2n × 2n 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

In amplitude modulation AM, if modulation index is more than 100% then: (1) Power of the wave increases. (2) Efficiency of transmission increases. (3) The wave gets distorted. (4) Bandwidth increases

asked May 29, 2018 in Electronics communication by Shimroz123
1 answer 22 views

What is the total resistance if 5 resistors of 20 Ω each are connected in series? A) 100 Ω B) 4 Ω C) 20 Ω D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 51 views

if the resistance is connected in parallel the total resistance decreases why?

asked Aug 14, 2017 in Electrical Engineering by Zeeshan
0 answers 14 views

If a dynamometer wattmeter is connected in an ac circuit, the power indicated by the wattmeter will be (a) volt-ampere product (b) average power (c) peak power (d) instantaneous power 

asked May 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 24 views

Two sinusoidal signals having the same amplitude and frequency are applied to the X and Y inputs of a CRO. The observed Lissajous figure is straight line. The phase shift between the two signals would be (1) Zero (2) 90 degrees (3) Either zero or 180 degrees (4) Either 90 degrees or 270 degrees  

asked May 28, 2018 in Electronics Engineering by Shimroz123
1 answer 14 views

 In thermo-couple instruments, in which of the following is an emf caused if the junction of two wires of dissimilar metals is heated and the free or cold ends are connected to a milli-voltmeter? A) Kelvin effect B) Hot wire effect C) Seebeck effect D) Faraday effect 

asked Jun 17, 2018 in Electronics Engineering by Shimroz123
1 answer 15 views

In a half-wave rectifier, if an a.c supply is 60 Hz. Then what is the a.c ripple at output? (A) 30 Hz (B) 60 Hz (C) 20 Hz (D) 15 Hz

asked Apr 26, 2018 in Electronics Engineering by Shimroz123
1 answer 17 views

In PCM system, if we increase the quantization levels from 2 to 8, the relative bandwidth requirements will:  (1) Be doubled (2) Remain same (3) Be tripled (4) Becomes eight times

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 18 views

What is the choice of size and number of generator units in interconnected power system?

asked Sep 7, 2018 by Shimroz123
0 answers 11 views

What is the Bode amplitude plot of a first-order lowpass system?  (A) Line with slope -40 dB/decade (B) Line with slope -20 dB/decade (C) Line with slope +20 dB/decade (D) Straight line parallel to the frequency axis

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

In the common–emitter transistor circuit, if the current gain is 100 and the collector current is 10 mA, the base current is: (1) 10 µA (2) 100 µA (3) 1 A (4) 10 A 

asked May 29, 2018 in Electronics Engineering by Shimroz123
1 answer 10 views

In amplitude modulation scheme, the over-modulation (A) is desired phenomenon (B) helps in signal recovery (C) is undesired phenomenon (D) Envelope of AM maintains the shape of the baseband signal

asked May 12, 2018 in Electronics Engineering by Shimroz123
0 answers 37 views

 The effect of phase error of local oscillator on spectral components in coherent detection of SSB Amplitude modulated signal is : a. The frequency of demodulated signals varies with fixed amplitude b. Amplitude of demodulated signals varies with fixed frequency c. Both amplitude & frequency vary d. The recovered signal has phase offset with fixed amplitude

asked Apr 12, 2018 in Electronics Engineering by Shimroz123
1 answer 60 views

To read or write a complete word from / to the memory in 8086 microprocessor and if it is located at an even address, the number of Read or Write cycles required is

asked May 23, 2018 in Microprocessors and Microcontrollers by Shimroz123
0 answers 45 views

For a balanced three phase star connected load for which line voltage is 230V and per phase resistance and reactance is 6 Ohm and 8 Ohm respectively. Calculate: 1) phase voltage 2) line current 3) power factor 4) total power absorbed

asked Aug 12, 2018 in Basic electrical and electronics engineering by Quiz
0 answers 10 views

A power system is represented by its system matrix ZBUS (m × m). Now an element is added in power system network without creating a new node. The dimension of the new impedance matrix will be (a) m × m (b) (m + 1) × (m + 1) (c) (m – 1) × (m – 1) (d) (m + 2) × (m + 2)  

asked May 25, 2018 in Power system by Shimroz123
0 answers 17 views

If modulation index is 0.6, maximum power efficiency (in %) of AM is about  A) 60 B) 30 C) 20 D) 10

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 17 views

A 12-bit ADC is operating with a lus clock period and total conversion time is seen to be 14us always. The ADC must be of the type  a. Flash type b. Counting type c. Integrating type d. Successive approximation type

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 52 views

If Ф = angle(G(jw)H(jw)) where w is the gain crossover frequency of Bode plot of the system, phase margin is  A) -180+ Ф B) 180- Ф C) 180+ Ф D) -180- Ф

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 21 views

For an 8 bit DAC, reference voltage is 10 V. If input to DAC starting from MSB is 10111100, output (in volts) is  A) 5.8 B) 6.4 C) 7.3 D) 8.2

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 20 views

A single-phase ac voltage source has 200 V rms and a system connected consumes an active power of 300 W. What is the reactive power consumed by the system if 2.5 A rms current is drawn ?  (a) 100 VAR (b) 200 VAR (c) 300 VAR (d) 400 VAR

asked Apr 23, 2018 in Electrical Engineering by Zeeshan
1 answer 21 views

In a graph, the number of independent loops is 6 and the number of independent cut sets is 5, The total number of branches in the graph is A) 9 B) 12 C) 10 D) 11

asked May 24, 2018 in Network Analysis by Shimroz123
1 answer 16 views

In D/A converter, the resolution required is 50mv and the total maximum input is 10v. The number of bits required is   (A) 7 (B) 8 (C) 9 (D) 200

asked May 17, 2018 in Digital Instrumentation by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,450 questions

7,047 answers

133 comments

3,086 users

...