18 views
in Electrical Engineering by
A single-phase AC arc welding transformer supplies approximately 

 (a) 100 volts at 0.35 power factor (b) 60 volts at 0.35 power factor (c) 220 volts at 0.8 power factor (d) 100 volts at 0.6 power factor

Your answer

Thanks for your contribution. Feel free to answer this question. Please avoid short answer. Your answer is most welcome. Be genuine.

Upload image or document:

Your name to display (optional):
Privacy: Your email address will only be used for sending these notifications.
Anti-spam verification:
Are you a robot ? (Y = Yes / N = No)
To avoid this verification in future, please log in or register.

Related questions

0 answers 88 views

A single phase 60 Hz generator supplies an inductive load of 4500kW at a power factor of 0.80 lagging by means of a 20 km long overhead transmission line. The line resistance and inductance are 0.0195 ohm and 0.60 mH per km. The voltage at the receiving end is required to be kept constant at 10.2 kV. Find the voltage regulation of the line.  (A) 12.59% (B) 16.34% (C) 32.68% (D) 41.15% 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 24 views

A single phase 230 V/ 150 V , 1 kVA, 50 Hz transformer is supplied by 230 V AC supply. Find the full load primary and secondary current. 

asked Sep 1, 2018 by Quiz
1 answer 7 views

A single-phase, 230 V, 50 Hz ac mains fed step down transformer (4:1) is supplying power to a half-wave uncontrolled ac-dc converter used for charging a battery (12 V dc) with the series current limiting resistor being 19.04 Ohm. The charging current is  (A) 2.43 A (B) 1.65 A (C) 1.22 A (D) 1.0 A

asked May 18, 2018 in Power electronics converters by Shimroz123
1 answer 24 views

A single phase fully controlled bridge converter supplies a load drawing constant and ripple free load current, if the triggering angle is 30o, the input power factor will be  (A) 0.65 (B) 0.78 (C) 0.85 (D) 0.866

asked May 18, 2018 in Power Electronics by Shimroz123
1 answer 17 views

 A single-phase transmission line of impedance j 0.8 ohm supplies a resistive load of 500 A at 300 V. The sending end power factor is?

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 20 views

A single-phase ac voltage source has 200 V rms and a system connected consumes an active power of 300 W. What is the reactive power consumed by the system if 2.5 A rms current is drawn ?  (a) 100 VAR (b) 200 VAR (c) 300 VAR (d) 400 VAR

asked Apr 23, 2018 in Electrical Engineering by Zeeshan
0 answers 21 views

A single phase fully controlled thyristor bridge ac -dc converter is operating at a firing angle of 25 degree and an overlap angle 10 degree with constant dc output current of 20A. The fundamental power factor (displacement factor) at input ac mains is : (A) 0.78 (B) 0.827 (C) 0.866 (0) 0.9

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 41 views

A 230 V/460 V single-phase transformer operating at 20 A and unity power factor has primary referred resistance of 0.2 Ω and reactance of 0.5 Ω. The approximate primary induced emf is (A) 216 V (B) 226 V (C) 234 V (D) 236 V

asked Apr 28, 2018 in Electrical Engineering by Shimroz123
1 answer 42 views

The primary turns of a 444 V/222 V, 50 Hz single-phase transformer with a core cross-sectional area of 100 cm2, and a maximum flux density of 1.0 T is (A) 100 (B) 200 (C) 222 (D) 400

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 30 views

A two -winding single phase transformer has a voltage regulation of 4.5% at full - load and unity power -factor. At full -load and 0.80 lagging power-factor, the voltage regulation will be: (A) 4.5% (B) less than 4.5% (C) more than 4.5% (D) none of the above

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
0 answers 109 views

A single phase transformer rated at 3000 kVA, 69 kV 4.16 kV, 60 Hz has a total internal impedance Zp of 127 ohm, referred to the primary side. Calculate the primary current if the secondary is accidentally short circuited.  (A) 43.5 A (B) 543 A (C) 9006 A (D) 721 A 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

if the rated voltage from the power lines is applied to the primary of a single-phase transformer which is operated on no-load, then

asked Apr 1, 2018 in Electrical Engineering by Shimroz123
1 answer 8 views

Arc welding uses following electric supply (A) ac (B) dc (C) both ac and dc (D) spiral waveform 

asked Apr 23, 2018 in Electrical Engineering by Shimroz123
0 answers 9 views

 Which of the following generators is used for DC arc welding application ? (A) Series generator (B) Shunt generator (C) Differential compound generator (D) Over -compound generator

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 7 views

Electric arc welding process produces temperature upto   (a) 1000 °C (b) 1500 °C (c) 3500 °C (d) 5550 °C 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 17 views

 Which single phase ac motor will you select for record players and tape recorders?  a) Hysteresis motor b) Shaded pole motor c) Reluctance motor d) Two value capacitor motor

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

In general AC distribution systems, arc interruption in vacuum circuit breakers are designed to function in a time period of (a) One cycle (b) Two to three cycles (c) Within ten cycles (d) None of the above

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

A single-phase fully controlled thyristor bridge ac-dc converter is operating at a firing angle of 25o and an overlap angle of 10o with constant dc output current of 20 A. The fundamental power factor (displacement factor) at input ac mains is  (A) 0.78 (B) 0.827 (C) 0.866 (D) 0.9

asked May 18, 2018 in Power electronics converters by Shimroz123
1 answer 28 views

A three-phase transformer, connected in star-delta, is composed of three single-phase transformers, each rated 127/ 13.2 kV. The line-to-line voltage ratio for the three-phase transformer is: A) 220 / 13.2 kV B) 127 / 13.2 kV C) 127 / 220 kV D) 220 / 220 kV

asked Jun 4, 2018 in Three phase transformers by Shimroz123
0 answers 70 views

The magnetizing reactance of a 4 kV/ 400 V, 50 Hz single-phase transformer on low voltage side is 35 Ω. The magnetizing reactance on the high voltage side is (A) 0.35 Ω (B) 3.5 Ω (C) 350 Ω (D) 3500 Ω

asked Jun 4, 2018 in Single phase transformer by Shimroz123
0 answers 18 views

At maximum efficiency of a single-phase transformer, the load power factor is (A) unity (B) lagging (C) leading (D) zero 

asked Jun 4, 2018 in Single phase transformer by Shimroz123
1 answer 13 views

A single phase transformer is designed to operate from 50 Hz, 1100 V supply and to have an output voltage of 240 V at no load. The core has mean area of 30 cm2 and the flux density has not to exceed 1.3T. The number of secondary turns will be (a) 1270 (b) 1017 (c) 768 (d) 277  

asked May 25, 2018 in Single phase transformer by Shimroz123
1 answer 24 views

A single-phase transformer has a turns ratio of 1 :2 and is connected to a purely resistive load as shown in the figure. The magnetizing current drawn is 1A, and the secondary current is 1A. Ifcore losses and leakage reactances are neglected, the primary current is  A)1.41A B)2A C) 2.24A D)3A

asked May 20, 2018 in Transformer by Shimroz123
1 answer 18 views

A single-phase, 50 kVA, 250 V/500 V two winding transformer has an efficiency of 95% at full load, unity power factor. If it is re-configured as a 500 V/750 V auto-transformer, its efficiency at its new rated load at unity power factor will be  (A) 95.752% (B) 97.851% (C) 98.276% (D) 99.241%

asked May 17, 2018 in Transformer by Shimroz123
1 answer 25 views

A single-phase transformer has no-load loss of 64 W, as obtained from an open circuit test. When a short-circuit test is performed on it with 90% of the rated currents flowing in its both LV and HV windings, he measured loss is 81 W. The transformer has maximum efficiency when operated at  (A) 50.0% of the rated current (B) 64.0% of the rated current (C) 80.0% of the rated current (D) 88.8% of the rated current

asked May 17, 2018 in Transformer by Shimroz123
1 answer 21 views

a single phase full wave midpoint thyristor converter uses a 230/200V transformer with centre tap on the secondary side. The P.I.V per thyristor is   (A) 100V (B)141.4V (C)200V (D)282.8V

asked May 17, 2018 in Power electronics converters by Shimroz123
1 answer 41 views

The hysteresis and eddy current losses of a single phase transformer working on 200 V, 50 Hz supply are Ph and Pe respectively. The percentage decrease in these when operated on a 160 V, 40 Hz supply are   (a) 32, 36 (b) 20, 36 (c) 25, 50 (d) 40, 80 

asked May 13, 2018 in Transformer by Shimroz123
1 answer 46 views

A single phase transformer has resistance and reactance of 0.2 pu and 0.6 pu respectively. Its pu voltage regulation at 0.8 pf lagging would he

asked May 3, 2018 in Power system by Shimroz123
1 answer 27 views

In a single-phase transformer, the magnetizing current is (A) in phase with the no-load current (B) in quadrature with the no-load current (C) the product of no-load current and power factor (D) in phase with the flux in the core

asked Apr 28, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 15 views

If a 220/440 V, 50 Hz, 5 KVA, single-phase transformer operates on 220V, 40Hz supply with secondary winding open circuited: (A) both the eddy current and the hysteresis losses will decrease (B) both the eddy current and the hysteresis losses will increase (C) eddy current losses will remain the same but the hysteresis losses will increase (D) eddy current losses will increase but the hysteresis losses will remain the same

asked Apr 11, 2018 in Computer Engineering by Shimroz123
1 answer 34 views

A 10 kVA, 400 V/200 V single phase transformer with 10% impedance draws a steady short-circuit line current of   (a) 250A (b) 50 A (c) 150 A (d) 350 A 

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 14 views

Compare between Resistance welding and Arc welding on any six points.

asked Oct 12, 2018 in Industry Electrical Systems-II by Shimroz123
1 answer 15 views

The commonly used gases in tungsten arc welding are 1.Hydrogen and oxygen 2.Hydrogen and organ 3.Hydrogen and helium 4.Helium and argon

asked May 17, 2018 in Utilization of electrical energy by Shimroz123
1 answer 30 views

For arc welding current range is usually  (1) 10 to 15 A (2) 30 to 40 A (3) 50 to 100 A (4) 100 to 350 A

asked Apr 30, 2018 in Utilization of electrical energy by Shimroz123
1 answer 14 views

Identify the correct combination of respective Electric arc welding and Electric resistance welding methods :  (A) Butt welding and Seam welding  (B) Hydrogen shielding and Projection welding  (C) Seam welding and Coated electrode welding  (D) Coated electrode welding and Hydrogen shielding

asked Apr 30, 2018 in Utilization of electrical energy by Shimroz123
1 answer 10 views

The supply for arc welding is : 

asked Apr 29, 2018 in Utilization of electrical energy by Shimroz123
1 answer 24 views

Compare Single phase 25 kV AC and 1500 V DC track electrification.

asked Oct 10, 2018 in Industry Electrical Systems-II by Shimroz123
1 answer 8 views

Draw neat labeled diagram of single phase AC locomotive showing its various equipments of power circuit and give function of each equipment used in power circuit.

asked Sep 12, 2018 by Shimroz123
0 answers 26 views

Explain power in single phase AC circuit.

asked Mar 11, 2018 in Computer techniques in power system by Quiz
0 answers 98 views

An auto transformer having a transformation ratio of 0.8 supplies a load of 10 kW. The power transferred inductively from the primary to secondary is (a) 2 kW (b) 4 kW (c) 8 kW (d) 10 kW 

asked May 25, 2018 in Autotransformer by Shimroz123
1 answer 23 views

Why does a transformer only work with an AC supply?

asked Mar 14, 2018 in Electrical Engineering by Quiz
1 answer 14 views

Draw schematic diagram of welding transformer showing constructional features of a welding transformer. Also explain its working.

asked Sep 18, 2018 by Shimroz123
1 answer 226 views

Total instantaneous power supplied by a 3-phase ac supply to a balanced R-L load is

asked Apr 28, 2018 in Electrical Engineering by Shimroz123
1 answer 11 views

In a dc-ac 3-phase MOSFET bridge inverter circuit, the switches are marked in a sequence as 1, 2, 3 in the top-half and 4, 5, 6 in the bottom half of the bridge. The triggering sequence of switches that gives balanced output voltage is (A) 1, 2, 3, 4, 5, 6 (B) 1, 5, 3, 4, 2, 6 (C) 1, 6, 2, 4, 3, 5 (D) 1, 4, 2, 5, 3, 6

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 33 views

A large dc motor is required to control the speed of the blower from a 3 -phase ac source. The suitable ac to dc converter is, 3 -phase (a) Fully controlled bridge converter (b) Fully controlled bridge converter with freewheeling diode (c) Half controlled bridge converter (d) Converter pair in sequence control

asked Apr 25, 2018 in Electrical Engineering by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,518 questions

7,116 answers

135 comments

3,090 users

...