# During the resistance welding heat produced at the joint is proportional to

21 views

During the resistance welding heat produced at the joint is proportional to

(a) I2R (b) kVA (c) Current (d) Voltage

## Related questions

Heat in a conductor is produced on the passage of electric current due to?

If a 220 V heater is used on 110 V supply, the heat produced by it will be nearly (a) one half (b) twice (c) one-fourth (d) four times

The torque produced in wattmeter is proportional to

When an alternating current passes through an ohmic resistance the electrical power converted into heat is?

Which gas is produced during charging of a lead-acid battery

Which of the following statements is incorrect? A) During parallel resonance impedance at resonance is minimum B) During parallel resonance current is magnified C) During series resonance current at resonance is maximum D) During series as well as parallel resonance, the power factor is unity

The IF BW of a radar receiver is inversely proportional to the (A) Pulse width (B) prf (C) Pulse interval (D) Square root of the peak transmitted frequency

The maximum torque that a synchronous motor can deliver is proportional to (1) 1/V2 (2) 1/V (3) V (4) V2

Production of heat due to electric current is related to . (A) Ohm's law (B) Joule's law (C) Kelvin's law (D) Maxwell's law

The power factor of a spot welding machine is expected to be around (1) Unity (2) 0.8 lagging (3) 0.3-0.5 lagging (4) 0.8 leading

The purpose of inserting external resistance at the time of starting a d.c. motor is to (a) increase the starting torque. (b) increase the armature flux. (c) reduce the starting current. (d) reduce the armature flux.

For a fuse wire of diameter ‘d’, fusing current is proportional to   (a) √d (b) d1.2 (c) d1.5 (d) None of these

In an energymeter which coil carries the current proportional to supply voltage _____.

To limit the short circuit current during fault conditions: (1) Reactors are used (2) Capacitors are used (3) A coil of high inductive reactance as compared to its resistance is used (4) Both (a) and (c)

For an RLC series AC circuit, the current at series resistance is (a) maximum at lagging power factor (b) maximum at leading power factor (c) maximum at unity power factor (d) minimum at unity power factor

A dc shunt motor runs at 500 r.p.m at 220 V. A resistance of 4.5 Ω is added in series with the armature for speed control. The armature resistance is 0.5 ohms. The current to stall the motor will be (1) 44 A (2) 50 A (3) 44.4 A (4) 60 A

A 3-phase, 4-pole, 50Hz induction motor runs at a speed of 1440 rpm. The rotating field produced by the rotor rotates at a speed of ________ rpm with respect to stator field. (A) 1500 (B) 0 (C) 1440 (D) 60

A 220 V shunt motor develops a torque of 54 N-m at armature current of 10 A. The torque produced when the armature current is 20 A, is?

Identify the correct combination of respective Electric arc welding and Electric resistance welding methods :  (A) Butt welding and Seam welding  (B) Hydrogen shielding and Projection welding  (C) Seam welding and Coated electrode welding  (D) Coated electrode welding and Hydrogen shielding

In a particular meter, the deflecting torque is directly proportional to the current flowing through it, the type of meter is (a) moving coil (b) moving iron (c) induction (d) electro-static

The capacitance of the capacitor is directly proportional to the

Power in the wind is proportional to

The torque, in a_______ is proportional to the square of the armature current. (A) DC shunt motor (C) 2 -phase servomotor (B) stepper motor (D) DC series motor

Is the speed of alternator is directly proportional to frequency?

As we know when there is a joint in optical fiber then there will be some loss then this loss be minimized by  a. Using index matching fluid in the gap b. Making V-grooved splicing c. Both (a)and (b) d. Making carefully polishing

The voltage applied to the H.V. side of a transformer during S.C. test is 2% of the rated voltage. The core loss as the fraction of its rated core loss is (a) 4% (b) 0.4% (c) 0.25% (d) 0.04%

Kick fuses are used across relay coils to prevent relay operation during   (a) Heavy external faults (b) Inrush current of transformer when they are energised (c) Line to ground faults (d) Bolted faults

Electric are welding process produces temperature up to (1) 10000  C (2) 15000  C (3) 35000  C (4) 55500  C

For controlling the vibration of the disc of ac energy meter, damping torque is produced by

The torque produced in a 4-pole machine is 100 Nm. If machine is re-wound with 6 ploes, other things remaining the unchanged, then the torque produced would be (1) 66.67 Nm (2) 100 Nm (3) 150 Nm (4) 133.33 Nm

Non -loading heat run test on transformers is performed by means of