10 views
in Instrumentation and control by
Which of these is not a photoelectric device ? 

a) Photoconductive cells Photoemissive cells c) Photoresistive cells d) Photovoltaic cells

Your answer

Thanks for your contribution. Feel free to answer this question. Please avoid short answer. Your answer is most welcome. Be genuine.

Upload image or document:

Your name to display (optional):
Privacy: Your email address will only be used for sending these notifications.

1 Answer

0 votes
by

Which of these is not a photoelectric device ?  Photoresistive cells

Related questions

1 answer 11 views

Which of these is not a semiconductor?  a) Si b) Tungsten c) Germanium d) None of these

asked Apr 10, 2018 in Instrumentation and control by Shimroz123
1 answer 14 views

Which of these is a thick -film resistor: -  a) wire would resistor b) carbon composition resistor c) metal film resistor d) cermet film resistor

asked Apr 10, 2018 in Instrumentation and control by Shimroz123
1 answer 14 views

 Which of these represent short in a series circuit?  a) Increase in resistance b) Increase in current c) Increase in voltage d) Increase in conductance

asked Apr 10, 2018 in Instrumentation and control by Shimroz123
0 answers 24 views

Which of the following is not a sequential storage device?  (a) Magnetic disk (b) Magnetic tape (c) Paper tape (d) All of these

asked May 23, 2018 in Computer Engineering by Shimroz123
1 answer 16 views

Which power device of the following is not a current triggered device?  A) Thyristor B) GTO C) TRIAC D) MOSFET

asked May 20, 2018 in Power Electronics by Shimroz123
0 answers 15 views

Which of the following is not a protective device?  A) MCB B) FUSE C) ELCB D) None of the Above

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 10 views

Which of the following is not an input device? A. Touch screen B. Optical scanners C. Touch Pad D. Mouse Pad

asked Apr 12, 2018 in Computer Engineering by Shimroz123
1 answer 16 views

 Which of the following is not an electromagnetic device?  a) Hall transducer b) Transformer c) Speedometer d) Eddy current damping device

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 5 views

Which semiconductor device acts like a diode and two transistor : -  a) SCR b) Triac c) UJT d) Diac

asked Apr 10, 2018 in Instrumentation and control by Shimroz123
1 answer 4 views

Which is not the disadvantage of LVDT?  a) Relatively large displacement are required for appreciable differential output b) temperature affects the performances of transducer c) low hysteresis and electrical isolation d) the dynamic response is limited mechanically by the mass of the core and electrically by the frequency of applied voltage

asked Apr 10, 2018 in Instrumentation and control by Shimroz123
1 answer 12 views

Which of the following flip-flop do not have race problem ? a)T flip-flop b) D flip-flop c) JK flip-flop d) Master Slave flip-flop

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 11 views

Which of these is correct with respect to a product developed or a service performed?. a. Bad quality is acceptable, but bad grade is not. b. Bad grade is acceptable, but bad quality is not. c. Neither bad grade nor quality is acceptable. d. Grade and quality is the same thing.  

asked Aug 31, 2018 by Shimroz123
1 answer 21 views

Which among these is a type of internal wiring? A. Cleat wiring B. Conduit wiring C. CTS wiring 

asked May 29, 2018 in Electrical Engineering by Shimroz123
1 answer 8 views

Converter is a device for transforming (A) ac to dc (B) dc to dc (C) dc to ac (D) ac to ac

asked Apr 23, 2018 in Instrumentation and control by Shimroz123
1 answer 79 views

Give broad classification of maintenance with meaning of each type. State the factors on which ideal maintenance of electric rolling stock is judged. Give any two means to improve any one factor of these.

asked Sep 2, 2018 by Shimroz123
1 answer 12 views

In which of these is reverse recovery time nearly zero? (1) Zener diode (2) Tunnel diode (3) Schottky diode (4) PIN diode

asked May 28, 2018 in Diode by Shimroz123
1 answer 84 views

For the minimum phase system, which of these is the most appropriate one ?  (A) All poles are inside the unit circle in the z-plane  (B) All zeros are inside the unit circle in the z-plane  (C) All poles and zeros are inside the unit circle in the z-plane  (D) All poles and zeros are outside the unit circle in the z-plane

asked May 12, 2018 in Control System by Shimroz123
0 answers 20 views

Which of these descriptions is true of the step response of an overdamped system ? (a) it rises to a steady state value with no overshoot (b) it rises to a steady state value with little overshoot (c) it has an undershoot (d) it does not settle to a steady state value

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 38 views

 Which of the following is a negative-resistance microwave device for oscillator applications? A) IMPATT Diode B) Gunn Diode C) Snap diode D) Schottky Diode 

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
1 answer 24 views

Buchholz relay is used as a safety device with respect to which of the following? A) Audio transformers B) Oil filled power transformers C) Air core transformer D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

Which of the following is a Read Only Memory storage device? A. Floppy Disc B. Hard Disc C. CD ROM D. None of these

asked Apr 12, 2018 in Electronics Engineering by Shimroz123
0 answers 17 views

For measuring the frequency of an unknown A.C. source. Which of the following device is necessary to obtain a standard waveform?  (A) Operational amplifier (B) Astable multivibrator (C) Schmitt trigger (D) Monostable multivibrator

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 11 views

Which of these materials requires the least value of magnetic field strength to magnetize it?  a. Nickel b. Silver c. Tungsten d. Sodium chloride 

asked May 17, 2018 in Telecommunication Engineering by anonymous
1 answer 14 views

Consider the following statements. Which of these statements are correct ?  (1) Reactance relays are preferred for ground fault relaying  (2) Impedance relays are most suitable for:protecting long transmission lines  (3) Mho relays are best suited for long transmission line protection  (4) Reactance relays are widely used for protection of Medium transmission lines  (A) All of them (B) (1) and (3) (C) (2) and (4) (D) (1), (2) and (4)

asked Apr 29, 2018 in Power system by Shimroz123
1 answer 41 views

Name three conventional ways of generating power. Of these three, which one contributes maximum generation in India.

asked Apr 3, 2018 in Lesson 2 Generation, Transmission and Distribution of Electric Power an Overview by Shimroz123
1 answer 93 views

Which of the following is NOT a non-linear resistor? A) Varistor B) Precision resistor C) NTC thermistor D) PTC thermistor 

asked Jun 18, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

In a CRO which of the following is not a part of electron gun: (1) Cathode (2) Grid (3) Accelerating anode (4) X–Y plates 

asked May 29, 2018 in Oscilloscope by Shimroz123
2 answers 18 views

Which of the following components is not a part of hydro-electric plant ? (a) Penstock (b) Spillway (c) Surge tank (d) Economiser 

asked May 26, 2018 in Electric Power Generation by Shimroz123
0 answers 13 views

Which of the following is not a method of resistance measurement ? (a) Ammeter – Voltmeter method (b) Post – Office box method (c) Ohm – Meter method (d) Two wattmeter method 

asked May 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 48 views

Which one of the following is not a transducer in the true sense?   (A) Thermocouple (B) Piezoelectric pick-up (C) Photo voltaic cell (D) LCD.

asked May 17, 2018 in Transducers and sensors by Shimroz123
1 answer 8 views

for the voltage built-up a self-excited D.C. generator, which of the following is not an essential condition.  1.there must be some residual flux  2.field winding mmf must aid the residual flux  3.total field circuit resistance must be less than t critical value  4.armature speed must be very high

asked May 13, 2018 in DC generator by Shimroz123
1 answer 71 views

Which of the following is not a basic element of a transformer ?  1. Core 2. Primary winding 3. Secondary winding 4. Mutual flux 

asked May 13, 2018 in Transformer by Shimroz123
1 answer 13 views

Which of the following is not a source of reactive power? (A) Generators (B) Reactors (C) Resistors (D) Capacitors

asked May 13, 2018 in Electrical Engineering by Shimroz123
1 answer 27 views

Which of the following is not a part of transformer installation?  (A) Conservator (B) Breather (C) Buchholz Relay (D) Exciter

asked May 8, 2018 in Switchgear And Protection by Shimroz123
1 answer 56 views

Which of the following statements is not characteristic of a static magnetic field? (A) It is solenoidal. (B) It is conservative. (C) It has no sinks or sources. (D) Flux lines are always closed.

asked Apr 28, 2018 in Physics by Shimroz123
0 answers 9 views

 A high prf implies which of the following statement is not correct ? (A) Makes the return echoes easier to distinguish from noise (B) Makes target tracking easier with conical scanning (C) Increases the maximum range (D) Has no effect on the range resolution

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 29 views

Which of the following is not a base load plant ? (A) Thermal power plant (B) Pumped storage plant (C) Hydro power plant (D) Geothermal power plant

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
2 answers 116 views

Which of the following is not a non-linear element ? (A) Diode (B) Transistor (C) Heater coil (D) None of the above

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 22 views

Which one is not a correct type of circuit breaker: A. Over Head circuit breaker B. Miniature Circuit Breaker C. Earth Leakage Circuit Breaker D. Oil Circuit Breaker 

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 11 views

Which one is not a correct type of wattmeter? A. Dynamometer wattmeter B. Induction wattmeter C. Electrolyte wattmeter D. Electrostatic wattmeter 

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

Which of the following is not computer hardware? A. Printer B. CPU C. Monitor D. Antivirus  

asked Apr 12, 2018 in Computer Engineering by Shimroz123
0 answers 23 views

Which of the following is not a Web Browser?  (1) Netscape Navigator (2) Mozilla Firefox (3) Opera (4) Yahoo Massenger

asked Apr 11, 2018 in Computer Engineering by Shimroz123
0 answers 24 views

Which of the following is not a multimedia software  (1) MS-PowerPoint (2) Adobe-Flash (3) Macromedia Director (4) MS-Paint

asked Apr 10, 2018 in Computer Engineering by Shimroz123
0 answers 31 views

Which one of the following is not a powerpoint view?  (1) Slide Sorter view (2) Slide view (3) Slide show view (4) Sorter view

asked Apr 10, 2018 in Computer Engineering by Shimroz123
0 answers 15 views

Which of the following is not a component of .NET framework  (1) CLR (2) ASP.NET (3) Windows Forms (4) C++ compiler

asked Apr 10, 2018 in Computer Engineering by Shimroz123
0 answers 20 views

Which of the following is not a search engine?  (1) HotBot (2) AltaVista (3) Google (4) Hotmail

asked Apr 10, 2018 in Computer Engineering by Shimroz123
0 answers 13 views

Which one among these is an example for trivalent impurity?  (A) Phosphorus (B) Antimony (C) Gallium (D) Arsenic

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 12 views

A triac is a device which acts as a  A) Diode in forward direction and thrylistor in the reverse direction B) Thyristor in both directions C) Diode in both directions D) Thyristor in forward direction and diode in reverse direction

asked May 20, 2018 in Power Electronics by Shimroz123
0 answers 13 views

Transducer is a device which  (a) converts one form of power in to the other (b) is similar to transformer (c) converts one form of energy in to other (d) helps in measuring electricity

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

Methods of earthing not followed in practice are : -  a) Pipe or Rod earthing b) Plate earthing c) Disc earthing d) None of these

asked Apr 10, 2018 in Instrumentation and control by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,543 questions

7,142 answers

135 comments

3,090 users

...