Ask a Question
The sequence in which the speed is increasing in ascending order a. RAM b. Hard disk c. Cache d. Thumb...
The sequence in which the speed is increasing in ascending order
b. Hard disk
d. Thumb Drive/Memory Stick
(1) dbac (2) bdac (3) badc (4) abdc
to add a comment.
← Prev Question
Next Question →
to answer this question.
What is the correct sequence of the following materials in ascending order of their resistivity ?
Emitter follower is used for (a) reducing the gain (b) increasing the distortion (c) impedance matching (d) none of these
Which of the following is not computer hardware? A. Printer B. CPU C. Monitor D. Antivirus
The most efficient method of increasing the speed of a 3.75KW d.c. shunt motor would be ...
In air-core cable the surge voltage travels approximately at the speed of light and a cable of 100m length gives a delay of a. 0.666μsec b. 0.333μsec c. 1.555μsec d. 1μsec
Write a program to sort an 1-d array in ascending order.
Total numbers of ascending runs in the sequence 4 6 7 2 9 1 2 8 9 3 0 (1) 3 (2) 5 (3) 7 (4) 9
The ascending order of a data hierarchy is
Of the following, ____ is not a computer language. a) MS-Word b) C++ c) COBOL d) BASIC
Of the following, ____ is different from the group. a) Windows b) MS-Word c) MS-Excel d) MS-PowerPoint
The no load speed of a d.c. shunt motor is 1140 rpm. At full load, the armature reaction weakens the main...
Which one is a vector quantity out of the followings? A. Energy B. Volume C. Area D. Force
Find the odd one out A) MS -Excel B) Windows XP C) Linux D) DOS
As there is no back e.m.f. at the instant of starting a D.C. motor, in order to prevent...
Discuss about the Hard Disk Drive housed in your PC. Is it an RTES?
Which of the following quantity maintains the same direction whether a D.C. machine runs as a generator or as a motor a. Induced e.m.f. b. Armature Current c. Field Current d. Supply Current
Computer keyboard can be classified as ________device. A. Memory B. Input C. Output D. Storage
When The dc converter in figure shown has a resistance load of R = 10 Ω and the input voltage is Vs 220 V the converter switch remains on, its voltage drop is Vo -2 V. The chopping frequency is fI K sW Vs If the duty cycle is 50%, determine: (a) the average output voltage V (b) the RMS output voltage Vo (c) the converter efficiency (d) the effective input resistance of the converter
In 8086 microprocessor , the address bus is ________ bit wide A. 12 bit B. 10 bit C. 16 bit D. 20 bit
The torque speed characteristic of a repulsion motor resembles which of the following d.c. motor
The band gap of elements arranged in ascending order is :
If residual magnetism is present in a D.C. generator, the induced e.m.f. at zero speed will be?
In D.C. machines the residual magnetism is of the order of?
In computer system Scanner is _________device. A. Input B. Output C. Both D. None
Conductance is measured in: A. Henries B. Mhos C. Hertz D. Watts
Calculate the resistance value in ohms for the following conductance values: (a) 0.002 S (b) 0.004 S (c) 0.00833 S (d) 0.25 S.
Calculate the resistance value in ohms for the following conductance values: (a) 0.001 S (b) 0.01 S (c) 0.1 S (d) 1 S.
If brushes of a D.C. generator are moved in order to bring these brushes in magnetic neutral axis, there will be?
In a D.C. shunt motor, speed is?
The widely used series-parallel system of speed control of d.c. series motors in traction work gives a speed
With the increase in load on a d.c. shunt motor, speed of the motor
In case the back e.m.f. and the speed of a D.C. motor are doubled, the torque developed by the motor will?
Which of the following disk scheduling techniques has a drawback of starvation?
Which of the following permutation can be obtained in the output (in the same order) using a stack assuming...
The heating time constant of a totally enclosed motor is relatively Select one: a. higher b. lower c. independent of type of enclosure. d. small
E is taller than D, C is taller than E, A is taller than E and B is taller than C. Who is the second shortest? Options: 1)D 2)E 3) A 4)C
The necessary condition to diagonalise a matrix is that (A) its all Eigen values should be distinct. (B) its Eigen vectors should be independent. (C) its Eigen values should be real. (D) the matrix is non-singular.
The IF is called as _________ A. initial flag B. indicate flag C. interrupt flag D. inter flag
The OF is called as _______ A. overflow flag B. overdue flag C. one flag D. over flag
The SF is called as ________ A. service flag B. sign flag C. single flag D. condition flag
The CF is known as ________ A. carry flag B. condition flag C. common flag D. single flag
The work of EU is ________ A. encoding B. decoding C. processing D. calculations
The intel 8086 microprocessor is a _______ processor A. 8 bit B. 16 bit C. 32 bit D. 4 bit
If the no load voltage of a certain generator is 220V and the rated load voltage is 200V, then the voltage regulation is: a. 1% b. 10% c. 20V d. 9%
The following is correct : (A) P = V x I (B) P = I ² x R (C) P = V ² / R (D) All of the above
A transmission line of 200 km has a certain A, B, C and D parameters. If the length is reduced to 60 km
In case of D.C. shunt motors the speed is dependent on back e.m.f. only because?
When two D.C. series motors are connected in parallel, the resultant speed is?
In river crossing, hilly terrain, modern HV lines have span more than (a) 50 m (c) 500 m (b) 100 m (d) 800 m
Converting 7,000 nA into microampere will result in: A. 0.007 µA B. 0.7 µA C. 700 µA D. 7 µA