Can you help by answering this question?

What is the difference between a soft start and a VFD?

54 views
in Electrical Engineering by
A moving coli ammeter has a fixed shunt of 0.02 Ω with a coil circuit resistance of R=1 kΩ and needs potential of 0.5 V across it for full scale deflection. Calculate the value of shunt to give full scale deflection when the total current is 10 A. (1) 0.05 Ω (2) 0.005 Ω (3) 0.5 Ω (4) 0.0005 Ω

Related questions

1 answer 23 views

A 10A DC Ammeter has a resistance of 0.1 Ω is to be extended to 50 A, the required shunt wire is A) Manganin wire of 20 m Ω B) Constantan wire of 20 m Ω C) Manganin wire of 25 m Ω D) Constantan wire of 25 m Ω

asked Jun 4, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 17 views

DC ammeter has a resistance of 0.1 Ω and its current range is 0-100 A. If the range is to be extended to 0-300 A, what shunt resistance need to be connected?  A) 0.025 Ω B) 0.05 Ω C) 0.015 Ω D) 0.03 Ω

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

A moving coil meter has a resistance of 3 Ω and gives full scale deflection with 30 mA. To measure voltage up to 300 V, the external resistance to be connected in series with the instrument is (A) 9997 Ω (B) 10000 Ω (C) 997 Ω (D) 10003 Ω

asked Apr 28, 2018 in Power Electronic Controlled Drives by Shimroz123
1 answer 21 views

A permanent magnet moving coil ammeter has a coil resistance of 99 ohm and Full Scale Deflection (FSD) current of 0.1mA. Shunt resistance is 1 ohm. Current through the meter at 0.5 F.S.D is:

asked May 22, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 17 views

A PMMC instrument has FSD of 100 μA and a coil resistance of 1 kΩ. To convert the instrument into an ammeter with full scale deflection of 100 mA, the required shunt resistance is (A) 1 Ω (B) 1.001 Ω (C) 0.5 Ω (D) 10 Ω

asked Apr 28, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 21 views

A dc shunt motor runs at 500 r.p.m at 220 V. A resistance of 4.5 Ω is added in series with the armature for speed control. The armature resistance is 0.5 ohms. The current to stall the motor will be (1) 44 A (2) 50 A (3) 44.4 A (4) 60 A  

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

A forward potential of 10V is applied to a Si diode. A resistance of 1 KΩ is in series with the diode. The current through the diode is

asked May 14, 2018 in Diode by Shimroz123
0 answers 11 views

Series resistance required to read 0-250 V with a moving coil instrument of internal resistance 2 ohm and full scale deflection of 50 mA is (a) 49998 Ω (b) 4998 Ω (c) 498 Ω (d) 49.8 Ω

asked May 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 16 views

For a resonant circuit with resonant frequency of 1 MHz a, 0 = 50 and R = 400, find the value of C (A) 250 pF (B) 1000 pF (C) 1.25 pF (D) 500 pF

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

Consider a cube of material of sides 1 cm with a resistance of 0.003 Ω between its opposite faces. What is the resistance if the same volume of the material is drawn into a length of 50 cm with a uniform cross – section? A) 0.003 Ω B) 0.15 Ω C) 7.5 Ω D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

A moving coil instrument of resistance 5 Ohm requires a potential difference of 75 mV to give a full scale deflection. The value of shunt resistance needed to give a full scale deflection at 30 A is

asked Apr 23, 2018 in Electrical Engineering by Shimroz123
0 answers 21 views

A ramp voltage V(t)=100 V is applied to an RC differentiating circuit with R=5 kΩ and C=4 μF. The maximum output voltage is  (A) 0.2 V (B) 2 V (C) 10 V (D) 50 V

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 12 views

The amount of current flowing through a circuit with a 40 V source and 6.8 kΩ of resistance is equal to: A. 27.2 mA B. 59 mA C. 5.9 mA D. 590 mA

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
0 answers 49 views

A high-pass filter has a resistance R = 2 kΩ The lowest input frequency to be passed is 7.5 kHz. The value of suitable coupling capacitor must be: A) 0.001 pico Farad B) 0.01 pico Farad C) 0.1 pico Farad D) 1 pico Farad

asked Jun 4, 2018 in Electrical Engineering by Shimroz123
0 answers 90 views

 When The dc converter in figure shown has a resistance load of R = 10 Ω and the input voltage is Vs 220 V the converter switch remains on, its voltage drop is Vo -2 V. The chopping frequency is fI K sW Vs If the duty cycle is 50%, determine: (a) the average output voltage V (b) the RMS output voltage Vo (c) the converter efficiency (d) the effective input resistance of the converter

asked Apr 26 by Hussein
1 answer 29 views

An OP amp has an open loop gain of 1,00,000. If the feedback fraction is 0.02, the approximate closed loop gain is (a) 1 (b) 1,00,000 (c) 50 (d) 0.02

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 27 views

A high pass filter has a resistance R = 2 kΩ. The lowest input frequency to be passed is 7.5 KHz. The value of suitable coupling capacitor must be : (A) 0.1 pF (B) 1 pF (C) 0.1 μ F (D) 1 μ F

asked Mar 31, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

A moving coil instrument has a resistance of 10 W and gives full scale deflection when carrying a current of 50 mA. To measure current upto 100 A, we will have to connect • 10 W resistance in series • 10 W resistance in parallel • 10/1999 W resistance in series • 10/1999 W resistance in parallel

asked May 13, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 12 views

An ammeter has a current change of 0—5A and its internal resistance is 0.2 ohm. In order to Change the range to 0-25 A, wear need to add a resistance of  A) 0.8 ohm in series with the meter B) 1.0 ohm in series with the meter C) 0.04 ohm in parallel with the meter D) 0.05 ohm in parallel with the meter

asked May 20, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 9 views

A series RLC circuit has a resistance of 50 , inductance of 0.4H and a capacitor of 10µF. The circuit is connected across a 100V supply. The resonance frequency and the current through the resistance are 

asked Mar 31, 2018 in Electrical Engineering by Shimroz123
1 answer 47 views

The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is 220 V. With the potential coil connected on the load side, the meter indicates 100 W. Approximate percentage error due to wattmeter connection is (A) 11% (B) 9% (C) 1.1% (D) 3%

asked Apr 25, 2018 in Instrumentation and control by Shimroz123
1 answer 14 views

A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is (A) 300 W (B) 150 W (C) 45 W (D) 20 W

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 43 views

For a short transmission line with r/x ratio of is 1.0, the regulation will be zero when the load power factor is

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
1 answer 32 views

A series RLC circuit has a resonant frequency of 1 KHz and a quality factor Q = 100. If each of the R,L and C is doubled from its original value, the new Q of the circuit is:  (1) 25 (2) 50 (3) 100 (4) 200

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 25 views

A nichrome wire used as heater coil has the resistance of 1 ohm/m. For a heater of 1000 W at 200 V, the length of wire required will be 

asked Mar 31, 2018 in Electrical Engineering by Shimroz123
0 answers 38 views

A balanced Delta connected load supplied with 440 V 50 Hz three phase AC supply has R=10 Ohm and L=0.6 mH in is each arm. Calculate line and phase current, active power.

asked Aug 12, 2018 in Basic electrical and electronics engineering by Quiz
1 answer 118 views

A cube of material of side 1 cm has a resistance of 0.002 ohm between its opposite faces. If the same volume of the material has a length of 8 cm and a uniform cross-section, the resistance of this length will be 

asked Mar 31, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

The e.m.f. induced in the armature of a shunt generator is 600 V. The armature resistance is 0.1 ohm. If the armature current is 200 A, the terminal voltage will be?

asked Mar 21, 2018 in DC generator by Shimroz123
1 answer 26 views

A moving coil of meter has 100 turns, and a length and depth of 10mm and 20mm respectively. It is positioned in a uniform radial flux density of 200 mT. The coil carrier current capacity is 50 mA. The torque on the coil is

asked Apr 29, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 16 views

The current coil of a wattmeter is connected to the C.T. of R phase. Its potential coil is connected across Y & B phases. The wattmeter measures (a) active power in R phase (b) active power of Y-phase (c) reactive power in R-phase (d) power proportional to 3-phase power if the load is balanced 

asked May 25, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 17 views

A binary ladder with R -2R network has R = 20K Ohms. The total resistance looking out toward the LSB input is (a) 20KOhms (b) 40KOhms (c) 10KOhms (d) 30KOhms

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 25 views

If resistance is 20 Q. and inductance is 27 in a R-L series circuit, then time constant of this circuit will be?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V, variable frequency supply. The current drawn by the circuit is found to be minimum when the supply frequency is 1 kHz. The approximate values of Q-factor and bandwidth are, respectively (A) 40, 400 Hz (B) 10, 100 Hz (C) 20, 50 Hz (D) 50, 20 Hz

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
0 answers 18 views

A parallel combination of capacitance C and resistance R is connected in series with inductance L and small resistance r. Under what condition will the circuit be non-reactive?  (A) C=LR (B) C=LR2 (C) C=L/R2 (D) C=L/R

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 22 views

A series R-L-C Circuit has a resonant frequency of 1000 Hz. If the values of R, L and C are doubled, the new resonant frequency is

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 28 views

Consider a circuit with four 10 Ω resistors connected in parallel and the current flowing through the circuit is 5 A. What will be the current if the above 4 resistors are connected in parallel? A) 5 A B) 50 A C) 500 A D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
0 answers 13 views

 A single phase, 2000V alternator has armature resistance and reactance of 0.8 ohm and 4.94 ohm respectively. The voltage regulation of the alternator at 100A, 0.8 leading pf is (A) 7% (B) - 8.9% (C) - 6.3% (D) 0%

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 26 views

lf slip of an induction machine is 0.02 and the stator supply frequency is 50 Hz, what will be the frequency of the rotor induced e.m.f.? (A) 10 Hz (B) 50 Hz (C) 1 Hz (D) 2500 Hz

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
0 answers 17 views

A DC shunt generator supplies 450 A at 230 V. The resistances of shunt field and armature are 50 Ω and 0.025 Ω respectively. What will be the armature voltage drop?  (A) 11.24 V (B) 22.7 V (C) 31.6 V (D) 38.4 V 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 27 views

A star circuit has element of resistance R/2. The equivalent delta elements will be?

asked Mar 25, 2018 in Network Analysis by Shimroz123
0 answers 29 views

A star arrangement of resistances has branch resistance of 3 Ω. The equivalent delta arrangement will have resistance of values (1) 9 Ω (2) 6 Ω (3) 3 Ω (4) 1 Ω

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
0 answers 23 views

A 1mA D' Arsonval movement has resistance of 100 Ω. It is to be converted to a 10 V voltmeter. The value of multiplier resistance is  (A) 999 Ω (B) 9999 Ω (C) 9900 Ω (D) 990 Ω 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

The current in a 200 mH coil increases from 2 to 5 A in 0.1 Second. What is rate of change of current? A. 30 A/s B. 20 A/s C. 10 A/s D. none of these

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 40 views

When 7/0.029 V.I.R cable is carrying 20 A, a drop of 1 V occurs every 12 m. The voltage drop in a 100 m run of this cable when it is carrying 10 A is nearly  (a) 4.2 V (b) 3.2 V (c) 1.2 V (d) 0.42 V

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
0 answers 30 views

A system function has a pole at s=0 and a zero at s= -1. The constant multiplier is unity. For an excitation cos(t), What is the steady-state response?  (A) √2sin(t+450) (B) √2sin(t-450) (C) sin(t-450) (D) Sin(t) 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

Draw a neat sketch of moving primary fixed secondary double sided LIM. Write one advantage and one disadvantage of it. 

asked Sep 2, 2018 by Shimroz123
0 answers 371 views

Internal resistance of a micro-ammeter is 500 ohm. Shunt resistance required to increase its range from 0-100 µA to 0-10 A will be approximately (a) 0.05 Ω (b) 0.005 Ω (c) 0.5 Ω (d) 5.0 Ω

asked May 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,450 questions

7,047 answers

132 comments

3,084 users

...