Can you help by answering this question?

What is the use of PWM in Arduino?

22 views
in Electrical Engineering by
The induced voltage across a coil with 250 turns that is located in a magnetic field and is changing at a rate of 8 Wb/s is A. 1,000 V B. 2,000 V C.31.25 V D. 3,125 V

1 Answer

0 votes
by

The induced voltage across a coil with 250 turns that is located in a magnetic field and is changing at a rate of 8 Wb/s is 2,000 V 

Related questions

1 answer 20 views

A coil of wire is placed in a changing magnetic field. If the number of turns in the coil is decreased, the voltage induced across the coil will: A. increase B. decrease C. remain constant D. be excessive

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
0 answers 24 views

What is the energy stored in the magnetic field at a solenoid of 40 cm long and 4 cm diameter wound with 100 turns of wire carrying a current at 20A?  (A) 0.705 Joule (B) 0.789 Joule (C) 0.587 Joule (D) 0.658 Joule 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

The voltage induced across a certain coil is 200 mV. A 1200 resistor is connected to the coil terminals. The induced current will be: A. 1.7 mA B. 16 mA C. 12 mA D. 120 mA

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 12 views

An iron ring of mean circumference 80 cm is uniformly wound with 500 turns of wire and carries 0.8A. Find the magnetic field strength. 

asked Sep 2, 2018 by Shimroz123
1 answer 8 views

The magnetic field intensity at the centre of a current carrying coil of diameter J m is K. The current flowing in the coil is

asked May 24, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 20 views

A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V, variable frequency supply. The current drawn by the circuit is found to be minimum when the supply frequency is 1 kHz. The approximate values of Q-factor and bandwidth are, respectively (A) 40, 400 Hz (B) 10, 100 Hz (C) 20, 50 Hz (D) 50, 20 Hz

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 22 views

The voltage across a coil, when di/dt = 20 mA/s and L = 8 H, is: A. 16 mV B. 160 mV C. 1.6 mV D. 2.5 mV

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
0 answers 16 views

A dynamometer type wattmeter with its voltage coil connected across the load side of instrument reads 250 W. If the load voltage be 200 V, what power is being taken by load? The voltage coil has resistance of 2000 Ω. (1) 200 W (2) 215W (3) 230 W /(4) 245 W

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 8 views

What is the percentage error when 3 resistors with ratings 100 Ω at 5%, 150 Ω at 6% and 250 Ω at 8% respectively, are connected in series? A) 6.33% B) 6.80% C) 19% D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 8 views

Induced draft fans are located at:

asked May 22, 2018 in Electrical Engineering by Shimroz123
1 answer 21 views

The magnetic field on the axis of a current carrying polygonal coil will have only a horizontal component parallel to the Plane of the coil 

asked May 24, 2018 in Electrical Engineering by Shimroz123
0 answers 11 views

Series resistance required to read 0-250 V with a moving coil instrument of internal resistance 2 ohm and full scale deflection of 50 mA is (a) 49998 Ω (b) 4998 Ω (c) 498 Ω (d) 49.8 Ω

asked May 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 13 views

At a particular temperature and current density, the critical magnetic field for a Type I superconductor is Bc and that for a type II superconductor ranges from Bc1 to Bc2 keeping other parameters unloaded. both superconductors are now subjected to a magnetic field B that satisfies the conditions B>Bc and Bc1 < ... will maintain a vortex state  (d) Type I superconductor will switch to the normal conducting state, while Type II superconductor will maintain a vortex sate

asked May 15, 2018 in Physics by Shimroz123
0 answers 28 views

 A DC shunt motor having unsaturated magnetic circuit runs at 1000 rpm with rated voltage If the applied voltage is reduced to half of the rated voltage, the motor will run at (A) 2000 rpm (B) 1000 rpm (C) 750 rpm (D) 500 rpm

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 60 views

To read or write a complete word from / to the memory in 8086 microprocessor and if it is located at an even address, the number of Read or Write cycles required is

asked May 23, 2018 in Microprocessors and Microcontrollers by Shimroz123
1 answer 13 views

If the secondary turns of a transformer are doubled and at the same time primary voltage is reduced to half then the secondary voltage will

asked May 15, 2018 in Transformer by Shimroz123
1 answer 98 views

When a conductor cuts magnetic flux, an emf is induced in the conductor. This is known as  (a) Joule's law (b) Faraday's law (c) Coulomb's law (d) Ampere’s law

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 12 views

The polarity of induced voltage while a field is collapsing is : - a) independent of the force creating the field b) opposite to the force creating c) the field identical to the force creating d) the field present only if the force is stationary

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 16 views

A coil of 500 turns is linked with a flux of 25 mwb, when carries a current of 12.5A. Calculate the value of self-inductance.

asked Sep 2, 2018 by Shimroz123
1 answer 24 views

lt the length, number of turns and area of a coil are  doubled, the inductance of the coil

asked Apr 26, 2018 in Electrical Engineering by Shimroz123
1 answer 33 views

Two heaters, rated at 1000 W, 250 V each are connected in series across a 250 V, 50 Hz ac mains. The total power drawn from the supply would be __________ watt.

asked Mar 31, 2018 in Control System by Shimroz123
1 answer 22 views

What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively? A) 320 V B) 448 V C) 64 V D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
0 answers 22 views

In a series RLC circuit, the rms value of voltage across the resistor is 30 V, across the inductor is 60 V and across the capacitor is 20 V. The rms supply voltage would be (A) 110 V (B) 10 V (C) 220 V (D) 50 V

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 16 views

According to Biot-Savart’s laws the magnetic field at a point due to incremental element of length dl carrying a current is  (A) Inversely proportional to the current carried by the element (B) Directly proportional to the current carried by the element (C) Directly proportional to the square of the distance (D) Inversely proportional to the length of the element

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 22 views

In large capacity transformers, 5% of the turns at the end of hv winding are provided with extra insulation so as to provide protection  (1) against corona (2) against lightning (3) due to surges occurring during switching operation (4) All of these

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 19 views

With a 12 V supply, a silicon diode, and a 370 - ohm resistor in series, what voltage will be dropped across the diode? a) 0.3V b) 0.7V c) 0.9V d) 1.4V

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 47 views

The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is 220 V. With the potential coil connected on the load side, the meter indicates 100 W. Approximate percentage error due to wattmeter connection is (A) 11% (B) 9% (C) 1.1% (D) 3%

asked Apr 25, 2018 in Instrumentation and control by Shimroz123
1 answer 17 views

In a series resonant circuit, maximum voltage across L occurs at  (a) Resonant frequency (b) Slightly below resonant frequency (c) Slightly above resonant frequency (d) At a frequency where I is maximum

asked Apr 23, 2018 in Electrical Engineering by Zeeshan
1 answer 13 views

A sine wave of 15 kHz is changing at a faster rate than a sine wave with a frequency of? B.12 kHz C.18 kHz D.1.3 MHz

asked May 15, 2018 in Basic concepts by Shimroz123
1 answer 18 views

The energy density of magnetic field in a magnetic circuit is (A) inversely proportional to magnetic flux density (B) directly proportional to the absolute permeability (C) directly proportional to the magnetic flux density (D) directly proportional to the square of magnetic flux density

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
0 answers 10 views

If the Disk head is located initially at 32, find the number of disk moves required with FCFS if the disk queue of I/O blocks requests are 98,37,14,124,65,67.  (1) 10 (2) 324 (3) 315 (4) 321 

asked Apr 10, 2018 in Computer Engineering by Shimroz123
0 answers 30 views

A coil having 90 turns is connected to a 120 V, 60 Hz source. If the effective value of the magnetizing current is 4 A. Calculate the inductance of the coil.  (A) 79.6 mH (B) 121.2 mH (C) 32.2 mH (D) 83.16 mH

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 21 views

The emf induced in a coil is 1 volt when current in it changes from 0 to 100 mA in time 10mS. Its inductance (in mH) value is  A) 10 B) 50 C) 100 D) 1000

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 12 views

The ratio of the primary to secondary voltage of a transformer is 2:1. The saving in the turns of weight of copper required if an autotransformer is used instead of two winding transformer is (1) 50% (2) 33.33% (3) 66.67% (4) 97% 

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

In a series RLC circuit at resonance, the magnitude of the voltage developed across the capacitor  A) Is always zero B) Can never be greater than the input voltage C) Can be greater than the input voltage, however, it is 90° out of phase with the input voltage D) Can be greater than the input voltage, and is in phase with the input voltage

asked May 20, 2018 in Network Analysis by Shimroz123
1 answer 26 views

A moving coil of meter has 100 turns, and a length and depth of 10mm and 20mm respectively. It is positioned in a uniform radial flux density of 200 mT. The coil carrier current capacity is 50 mA. The torque on the coil is

asked Apr 29, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 421 views

A shunt motor rotating at 1500 r/min is fed by a 120 V source. The line current is 51 A and the shunt field resistance is 120 ohm. If the armature resistance is 0.1 ohm, calculate the current in the armature.  (A) 1 A (B) 51 A (C) 50 A (D) 12 A 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 13 views

If the load current and flux of a DC motor are held constant, and voltage applied across its armature is increased by 10%, its speed will:  (A) Decrease by 10%. (B) Remain unchanged. (C) Increase by 10%. (D) Increase by 20%. 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 10 views

Which law states that induced e.m.f and current always opposes the cause producing them?

asked May 29, 2018 in Electrical Engineering by Shimroz123
1 answer 22 views

What is the charge on each capacitor when a 150 V is applied across two capacitors with values 5 μF and 10 μF, connected in series? A) 500 μC B) 0.5 μC C) 0.5 C D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 321 views

in a three-phase induction motor, the rotor field runs at the following speed with respect to the stator structure: 

asked May 22, 2018 in Induction Machine by Shimroz123
0 answers 25 views

A d.c. ampere-hour meter is rated at 5A, 250 V. The declared constant is 5 A sec/revolution. The constant in revolution/kwh will be (a) 2880 (b) 2680 (c) 2480 (d) 2280

asked May 25, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 65 views

What happens to the angle between current and voltage, when a small capacitance is added in series with a highly inductive circuit?  (A) Increases (B) Remains same as earlier angle (C) Decreases (D) Becomes indeterminant

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 21 views

A network that consists of at least a voltage source or current source is called A) Active network B) Ideal network C) Sourced network D) Outsourced network

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
0 answers 18 views

It is desired to illuminate a drawing hall with an average illumination of about 250 lux. The area of hall is 30 m × 20 m. The lamps are to be fitted at 5 m height. Find the number and size of incandescent lamps required for an efficiency of 12 lumen/watt. Utilization factor = 0.4 and maintenance factor = 0.85.   (a) 40 and 1000 W (b) 20 and 500 W (c) 60 and 1000 W (d) None of the above 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

A moving coil meter has a resistance of 3 Ω and gives full scale deflection with 30 mA. To measure voltage up to 300 V, the external resistance to be connected in series with the instrument is (A) 9997 Ω (B) 10000 Ω (C) 997 Ω (D) 10003 Ω

asked Apr 28, 2018 in Power Electronic Controlled Drives by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...