Recent questions tagged measurement

1 answer 22 views

Name two methods for measurement of low, medium and high resistance. Give one advantage and one limitation of V- I method.

asked Sep 6, 2018 by Shimroz123
1 answer 27 views

State the significance of term measurement. 

asked Sep 6, 2018 by Shimroz123
1 answer 17 views

Explain significance and purpose of electrical measurement system.

asked Sep 6, 2018 by Shimroz123
1 answer 3 views

Describe with working of LCR meter for measurement of inductance. 

asked Sep 6, 2018 by Shimroz123
1 answer 73 views

State any two disadvantages of one wattmeter method of measurement of 3 phase power.

asked Sep 6, 2018 by Shimroz123
1 answer 12 views

Explain V- I method of measurement of medium resistance. 

asked Sep 6, 2018 by Shimroz123
1 answer 26 views

What are the factors influencing measurement errors?

asked May 6, 2018 in Digital Instrumentation by Shimroz123
1 answer 56 views
1 answer 14 views

Measurement of a non -electrical quantity involves the following four subsystems:  a) amplifier block b) display block c) instrumentation block d) transducer block  The correct, sequence in which these block occur is  (1) d,a,c,b (2) d, c, a, b (3) a, c, b, d (4) a, b, c, d

asked Apr 29, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 15 views

The bridge most suited for accurate measurement of relative permittivity of dielectric materials is (A) Carey Foster Bridge (B) Anderson’s bridge (C) Heaviside Bridge modified by Campbell. (D) Schering Bridge.

asked Apr 28, 2018 in Control System by Shimroz123
1 answer 39 views

Accurate measurement of very low resistances is possible with (A) Megger (B) Wheatstone Bridge (C) Kelvin’s Double Bridge (D) Wagner’s Earthing Device

asked Apr 25, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 134 views

In a 3-phase power measurement by two wattmeter method, both the watt meters had identical readings. The power factor of the load was?

asked Mar 21, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 42 views

Explain the basic dual slope ADC technique used in digital multimeters with its diagram and measurement cycle.

asked Mar 2, 2018 in Digital Instrumentation by Quiz
1 answer 46 views

What is measurement error ?

asked Jan 7, 2018 in Digital Instrumentation by Quiz
To see more, click for the full list of questions or popular tags.

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,514 questions

7,113 answers

135 comments

3,090 users

...